Clear-Com CB-222 - Manual (Page 2)

● ● Slide●the●battery●door●off●by●pressing●
down●and●back.
● ● Install●the●battery●or●(3)●AA●batteries●
and●replace●the●battery●door.
● ● Press●and●hold●the●ON/OFF●button●
for●two●seconds;●the●MasterBelt●will●
vibrate●as●it●powers●up.●
● ● Power● the● MasterBelt● OFF● by●
pressing● and● holding● the● ON/OFF●
button●for●four●seconds.
2 sec
POWER ON
● ● Plug●a●headset●into●MasterBelt●and●each●BeltStation.
● ● To●set●Mic●Gain,●Press●MENU●and●scroll●down●to●Set●Controls.
● ● Scroll●to●Mic●Gain●and●Press●ENTER.
● ● Use●the●scroll●knob●to●set●the●Mic●Gain●for●the●headset●that●you●are●using;●speak●loudly●
into●the●microphone●until●you●have●reached●a●desirable●setting.●●The●blue●TALK●LED●
will●flash●red●to●indicate●clipping.●●Press●ENTER●to●save●at●desired●setting.
● ● Select●the●desired●communication●channel●by●pressing●the●A●or●B●channel●knob.
● ● Adjust●the●headset●listening●volume●by●turning●the●A●or●B●rotary●control.
● ● Press●the●TALK●button●to●talk●to●others●on●the●selected●channel●(the●blue●TALK●LED●will●
remain●lit●when●talk●is●enabled●on●that●channel)
● ● Confirm● the● desired● talk● channel● and● talk● status● by● observing● the● MasterBelt● and●
BeltStation●LCD●screen.
Power ON the MasterBelt
Start Communicating
● ● Confirm●the●MasterBelt●is●powered●ON.
● ● Confirm●the●BeltStation●is●powered●
OFF.
● ● Connect● the● 3.5mm● data● pairing●
cable● from● the● MasterBelt● to● the●
BeltStation.
● ● Power● ON● the● BeltStation● while●
observing● the● BeltStation● LCD●
screen;● the● BeltStation● will● vibrate●
and●“Pairing●Complete”●will●appear●
momentarily● on● the● LCD● screen● if●
pairing●was●successfull.
● ● The● BeltStation● will● return● to● the●
operational●screen●and●log●into●the●
MasterBelt.
● ● The●BeltStation●will●appear●in●the●first●available●slot●(1-5)●on●the●MasterBelt●LCD●screen.
● ● Repeat●for●each●BeltStation.
Note: MasterBelts and BeltStations are named to their default setting name. They can be
renamed.
5
1
3
● ● The●first●time●you●power●up●the●MasterBelt,●you●will●be●prompted●to●“select●
an●authorized●band●for●your●location”.
● ● There●are●seven●RF●bands●that●use●different●parts●of●the●2.4GHz●spectrum.
● ● Scroll●to●an●appropriate●band●for●your●location●and●press●Enter●to●select.●
● ● Press●MENU●to●return●to●the●operational●screen.
Band 1 is appropriate for most, but not all, locations worldwide (US is
band 1). Some countries require that you use a limited portion of the
2.4GHz band. It is the user’s responsibility to ensure that you select a
band that is permitted for use in your location.
Selecting the RF band
MHz
Band Start End Wide Avoid 802.11b/g
1 2400 2480 80 None
2 2400 2450 50 11
3 2423 2473 50 1
4 2431 2480 49 1,2
5 2400 2428 28 7,8,9,10,11
6 2423 2450 27 1,11
7 2453 2480 27 1,2,3,4,5,6,7
4
From●the●front●of●the●MasterBelt,●follow●the●steps●below●:●
1.● Press●MENU●(Main●Menu).●
2.● Scroll●to●Belt●Settings●and●press●ENT.●●
3.● Scroll●to●Tech●Menu●and●press●ENT.
●» A●warning●message●will●appear;●press●ENTER●to●proceed.
4.● Press●ENTER●for●Radio●Configuration.
5.● Press●ENTER●for●Network●Number●and●use●scroll●knob●to●select●a●network●number●
other●than●zero●and●press●ENTER●to●save●setting.
6.● Press●MENU●to●return●to●previous●menu;●scroll●to●Lockout●Key●and●use●scroll●knob●to●
select●a●lockout●key●other●than●255●and●press●ENTER●to●save●setting.
7.● Press●MENU●repeatedly●until●you●get●back●to●the●Operational●screen.
8.● Power●the●MasterBelt●OFF;●wait●10●seconds●and●power●the●MasterBelt●ON●again.
If you have multiple, collocated MasterBelts, ensure that you select different network
numbers for each MasterBelt configuration to help prevent interference between
units. See Reference Manual for more details.
Changing the Default RF Configuration
2
Pair BeltStations to the MasterBelt