Ultra Start 600 Series - Manual (Page 9)

Setting 1 - Car Finder/ 5th Channel
Menu 2- Alarm Settings
Setting 2 - Secure Valet Mode
Setting 3 - Park Light Output
Setting 4 - Horn Honk Timing
Setting 5 - 4th Channel Settings
Setting 6 - Car Jack Mode
Setting 7 - Horn/ 5th Channel
1 Car Finder OFF 1 Light Flash Car Finder Mode Disabled
*2 Car Finder ON 2 Light Flashes Car Finder Mode Enabled
**To operate the 5th channel on button #4, setting 7 must be programmed for 5th channel output.
1 Parking Lights on Disarm 1 Flash Park Lights on for 30 seconds on disarm
2 Negative Park Light 2 Flashes Switches Park Light and the Trunk Release outputs
3* Normal Parking Lights 3 Flashes 2 Park Light Flashes on disarm
1 5ms Pulsed Output 1 Flash Short (Quiet) Pulses
2 20ms Pulsed Output 2 Flashes Long (Loud) Pulses
*3 10ms Pulsed Output 3 Flashes Normal (Medium) Pulses
1 Secure Valet Active 1 Flash Ignition “ON” and valet switch held for 15 seconds
2* Normal Valet Active 2 Flashes Ignition “ON” and valet switch held for 5 seconds
Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
1 Pulsed Output 1 Flash Pulsed for 0.75 seconds upon 4th Channel Activation
2 Latched Output 2 Flashes Latched until repeated or ignition “ON”
*3 Active Output 3 Flashes Active for as long as the button is held on Transmitter.
1 Type 1 1 Flash Press button #4 or open the door while the Ignition is “ON”
2 Type 2 2 Flashes Press button #4 or by turning the Ignition “On”
*3 Car Jack OFF 3 Flashes No Car Jack Functions
1 5th Channel 1 Flash Pulsed output when activated by button #4
2 Horn Honk 2 2 Flashes Horn Honk Output - Full Alarm ONLY
*3 Horn Honk 1 3 Flashes Horn Honk with Arm & Disarm Chirps
Press the Valet Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the lock and Star buttons together to activate the 4th Channel output.
The Shock Sensor and ignition will be bypassed upon 4th channel activation.
PAGE 9
SECURITY SYSTEM
INSTALL GUIDE