Ultra Start 600 Series - Manual (Page 8)

Setting 1- Ignition Auto Lock
Menu 1 - User Settings
Setting 2- Horn Honk Settings
Setting 3- Door Lock Options
Setting 4 -Sensor - Enable / Disable
Setting 5 - Passive / Active Arming
Setting 6 - Active / Passive Locks
1 Double Pulse Unlock 1 Flash Single .75 second lock and double unlock pulse
2 3 Second Lock & Unlock 2 Flashes 3 second pulses for lock & unlock
*3 0.75 Second Pulses 3 Flashes 0.75 second pulses for lock and unlock
1 Passive Arming 1 Flash Auto Arms 30 seconds after last door is closed
2 Active Arming With Rearm 2 Flashes Unlock is pressed and no door is within 30 sec.
* 3 Active Arming 3 Flashes Alarm arm by remote transmitter only.
1 Sensors Disabled 1 Flash Shock sensor and Aux. Sensor disabled
* 2 Sensors Enabled 2 Flashes Shock Sensor and Aux. sensor enabled.
1 Active Locking 1 Flash Doors do not auto-lock with passive arming
*2 Passive Locks 2 Flashes Doors Auto-Lock with passive arming.
1 Ignition Lock & Unlock Enabled 1 Light Flash Doors Lock/Unlock when the key is turned On/Off
2 Ignition Lock Only 2 Light Flashes Doors Lock when ignition key is turned ON only
*3 Ignition Auto Lock Disabled 3 Light Flashes Doors do not Lock or Unlock with Ignition key
1 Lock & Unlock chirps Disabled 1 Flash A audible chirp for Panic Mode only
2 Lock & Unlock chirps Enabled 2 Flashes Chirp for Lock & Unlock but NO indication for Start
*3 Chirps Enabled 3 Flashes Chirp indication for Lock, Unlock and Start
Press the Valet Switch 1 time to select setting 1 (This will be confirmed by 1 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 2 times to select setting 2 (This will be confirmed by 2 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 3 times to select setting 3 (This will be confirmed by 3 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 4 times to select setting 4 (This will be confirmed by 4 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 5 times to select setting 5 (This will be confirmed by 5 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
Press the Valet Switch 6 times to select setting 6 (This will be confirmed by 6 LED flashes)
Press and hold the Valet Switch until you receive the appropriate # of park light flashes and/or siren chirps.
Release the Valet Switch. Press the Valet momentarily to move to next program step or repeat to change selection.
PAGE 8
SECURITY SYSTEM
INSTALL GUIDE