ClimaCool UCR 30, 50 and 70 tons Manual - Manual (Page 28)

www.climacoolcorp.com
28
Malfunction – Low Head Pressure Chart
3RVVLEOH&DXVH 5HPHG\
,QVXIÀFLHQWUHIULJHUDQWFKDUJHWRDGHTXDWHO\ÁRRG
FRQGHQVHU $GGUHIULJHUDQW
/$&IDLOVWRFORVHGXHWR
D)RUHLJQPDWHULDOLQYDOYH
E/RVVRIDLUFKDUJHLQHOHPHQW 6HH%HORZ
D&DXVH/$&WRRSHQE\UDLVLQJFRQGHQVLQJUHFHLYHU
SUHVVXUHDERYHYDOYHVHWWLQJE\F\FOLQJFRQGHQVHUIDQ,I
IRUHLJQPDWHULDOGRHVQRWSDVVWKURXJKYDOYHUHSODFH/$&
E5HSODFH/$&
/$&UHFHLYHUSRUWIDLOVWRRSHQGXHWR
D/HVVWKDWSVLSUHVVXUHGURSDFURVVLQOHWWRUHFHLYHUSRUW
E,QWHUQDOSDUWVGDPDJHGE\RYHUKHDWLQJZKHQLQVWDOOHG 6HH%HORZ
D&KHFN/$&FDXVHVUHPHGLHV
E5HSODFH/$&
'LVFKDUJHOLQHWR/$&UHVWULFWHG 5HPRYHUHVWULFWLRQLQÀWWLQJVRUOLQH
'LUW\FRQGHQVHUFRLO &OHDQFRLO
$LURQFRQGHVHUEORFNHGRII &OHDQDLUHDDURXQGFRQGHQVHU
7RRPXFKUHIULJHUDQWFKDUJH 5HPRYHFKDUJHXQWLOSURSHUKHDGSUHVVXUHLVPDLQWDLQHG
8QGHUVL]HGUHFHLYHU &KHFNUHFHLYHUFDSDFLW\DJDLQVWUHIULJHUDQWUHTXLUHGWR
PDLQWDLQGHVLUHGKHDGSUHVVXUH
1RQFRQGHQVLEOHVDLULQV\VWHP 3XUJHIURPV\VWHP
%\SDVVLQJKRWJDVZKHQQRWUHTXLUHGGXHWR
D,QWHUQDOSDUWVRIWKH,QOHWWRUHFHLYHUSRUWRIWKH/$&DUH
GDPDJHGE\RYHUKHDWLQJZKHQLQVWDOOHG
E,ISUHVVXUHGURSDFURVVWKHFRQGHQVHUDVVRFLDWHGSLSLQJ
DQG/$&H[FHHGVSVLXQGHUIXOOORDGFRQGLWLRQV 6HH%HORZ
D5HSODFH/$&
E&RQWDFW)DFWRU\
/LTXLGSRUWRUOLTXLGOLQHSOXJJHG 5HPRYHEORFNDJHLQSRUWRUOLTXLGOLQH
&RQGHQVHUIDQVQRWUXQQLQJ 5HSDLURUUHSODFHIDQPRWRU
0DOIXQFWLRQ+LJK+HDG3UHVVXUH
WARNING: Serious injury could result from an explosion
caused by the rapid expansion of trapped liquid refrigerant
subjected to high temperature. ALWAYS OPEN OR VENT
THE SYSTEM BEFORE APPLYING HEAT TO REMOVE SYSTEM
COMPONENTS. Break the element charging cap tube on
valve dome by hand or with a clean cut tool. DO NOT use
side cutters, which may seal the opening.
Installation Precautions
1. Do not overcharge — see charging procedures on
pages 26.
2. Be sure that the piping does not allow liquid refrigerant
to be trapped in sections where hydrostatic pressure
can develop.
3. Be sure that the receiver is large enough to hold the
entire charge during “warm” operation.
4. Do not overheat — see brazing procedures on page 25.
5. “Caution:” on page 25.
6. “Caution:” on page 27.