Alera Lighting AL1066 - A+CLASS Quick Start Guide - Manual (Page 2)

General / A/V,
Study Time
General / A/V,
Study Time, Whiteboard
General / A/V,
Dimming, Study Time
General / A/V, Dimming,
Study Time, Whiteboard
Teacher Station Options
On/Off
Master On/Off Control
Whiteboard On/Off
Row 1 On/Off Row 1, 2 On/Off Row 1, 2, 3 On/Off Row 1, 2, 3, 4 On/Off
Row On/Off Control Options
QUICK START COMMISSIONING
AL1066 9/13 72-00433
© 2013 Alera Lighting, a division of Hubbell Lighting, Inc. All rights reserved. US Patent #8,436,542.
Because of continuing product improvement programs, Alera Lighting reserves the right to change specifications without notice.
701 Millennium Blvd. Greenville, SC 29607
Tel 864.678.1000 Fax 866.898.0131
www.aleralighting.com
12 Hour AM or PM
1:00 AM
2:00 AM
3:00 AM
4:00 AM
5:00 AM
6:00 AM
7:00 AM
8:00 AM
9:00 AM
10:00 AM
11:00 AM
12:00 Noon
24 Hour 12 Hour AM or PM
13:00 1:00 PM
14:00 2:00 PM
15:00 3:00 PM
16:00 4:00 PM
17:00 5:00 PM
18:00 6:00 PM
19:00 7:00 PM
20:00 8:00 PM
21:00 9:00 PM
22:00 10:00 PM
23:00 11:00 PM
24:00 12:00 Midnight
BACK
SELECT
UP
DOWN
A+CLASS ™ qUICk STArT GUIde
BASIC
Standard Set-up: Scroll to BASIC menu - SELECT
1. Room ID
Default: Room 1
To change: Press SELECT. Flashing keybar indicates character
available to change. Use
t s buttons to scroll through
alphanumeric character list until letter or number desired
appears. Press SELECT to accept selection and move to the
next character. If no change is desired, press SELECT to skip.
When all changes are complete, press SELECT until # sign
appears, then press SELECT to accept all changes and return
to BASIC Room ID menu.
2. Date and Time
Default: 01/01/1972
To change: Use SELECT key to navigate, [
t s ] to scroll
through alphanumeric characters, SELECT to accept selections
and return to BASIC Date/Time menu. Note that time is
24-hour time format: see table below.
3. Number of Lamps (in cross section)
Default: 3
To Change: Scroll [
t s ] to the proper number of lamps in
cross section – SELECT. When counting lamps, use number of
lamps in cross section. See examples below.
4. Number of Rows
Number of Rows of GEN / A/V Lighting (does not include
whiteboard)
Default: 2
To Change: Scroll using Use
t s buttons to the number of
lighting rows installed in the classroom. SELECT.
5. Number of Whiteboards (whiteboard lighting)
Default: 1
To Change: Scroll [
t s ] to 0 or 2 – SELECT. This menu
item applies only to whiteboard lighting which is controlled
through the CCM.
ONE LAMP
TWO LAMP
THREE LAMP
When installing into wall boxes, care must be taken to remove excess CAT5 cable from box prior to installation.
Cable connections must remain straight and true, free of excess pressure, and properly aligned.
a
inCorreCt - do not store
exCess CabLe in eLeCtriCaL box CorreCt instaLLation of
switChes to eLeCtriCaL box a
a+CLass ™ ControLs QuiCk start Commissioning