Extron Electronics ISS 506 Setup Guide User Manual
Iss 506 • setup guide, Iss 506 • setup guide (continued), Installation and cabling features
ISS 506 • Setup Guide
NOTE: For full installation, configuration, and operation details, refer to
the ISS 506 User Guide, available at
www.extron.com
.
This guide provides quick start instructions for an experienced installer to set up and operate the
Extron ISS 506 Integration Seamless Switchers, a family of seamless, scaling, video and stereo audio switchers.
Installation and Cabling Features
100-240V
50/60 Hz
2A MAX
R/
R-Y
SDI
G/Y
VID
S
B/C
B-Y
H
H/HV
V
H/HV
RS232/422
1
L
R
R/
R-Y
1
2
G/Y
VID
B/C
B-Y
R/
R-Y
G/Y
VID
B/C
B-Y
H/HV
V
H/HV
V
V
R/
R-Y
3
4
G/Y
VID
B/C
B-Y
VID
/Y
R-Y
VID
B-Y
/C
V
G
/Y
5
R
R-Y
RESET
O
U
T
P
U
T
S
6
YC
B/
B-Y
PROGRAM
PREVIEW
RGB/R-Y, Y, B-Y
RGB/R-Y, Y, B-Y
2
L
R
3
L
R
4
L
R
5
L
R
6
L
R
I
N
P
U
T
S
L
R
PREVIEW
FIXED
L
R
PROGRAM
VARIABLE
L
R
LAN
LO-
RES
OUT
R-Y/
R
C
Y/
G
VID
B-Y/
B
Y
Scan Converter
DVI
3G/HD-SDI
3G/HD-SDI
OUT
DVI
OUT
PICTURE
ADJUSTMENTS
CONFIG
DETAIL
ZOOM
BRIGHT/
CONT
COLOR/
TINT
SIZE
POSITION
Rear Panel
Front Panel
SDI
VID
/Y
5
6
RGB/R-Y, Y, B-Y
PREVIEW
PROGRAM
11
1
13 12
14
2
5
10
7
3
4
6
8
9
Connections
a
AC power connector
h
Preview Output 15-pin HD connector
(RGB or component)
b
Inputs 1 through 4 configurable BNC connectors
i
Optional Program Output connector(s)
(RGB, component, RGBcvS, S-video, or composite)
(DVI, scan converted low resolution, or 3G/HD-SDI
†
)
c
Input 5 configurable BNC connectors
j
Output audio captive screw connectors
(component, S-video, composite)
d
Input 6 configurable mini-DIN and BNC connectors
k
LAN (Ethernet) RJ-45 port
(S-video, composite, SDI/HD-SDI*, auto SDI)
e
Input 1 through 6 audio captive screw connectors
l
RS-232/422 DB-9 port
f
Program Output BNC connectors
m
Reset button
(RGB or component)
g
Program Output 15-pin HD connector
n
Configuration port (front panel)
(RGB or component)
(RS-232 only on a 2.5 mm TRS connector)
* An SDI or HD-SDI input is preset only when an optional SDI or HD-SDI input card is installed (DI/DVI, DI/SC, and DI/3G-SDI models).
†
The output for
i
depends on the optional output card installed (DI/DVI, SC, DI/SC, and DI/3G-SDI models).
Step 1 — Mounting
Turn off or disconnect all equipment power sources. For tabletop use, affix
the rubber feet. For optional rack mounting, secure the supplied brackets
(see image at right) and mount in a rack.
Step 2 — Video inputs
a.
Inputs 1 through 4 — Connect RGB video, component video,
S-video, or composite video to these female BNC connectors.
b.
Input 5 — Connect NTSC or PAL component video,
S-video, or composite video to these female BNC
connectors as shown at right.
MBD 249
2U Rack Mount Bracket
(use four lower holes)
RGBHV
Video
Input 1 through 4 Configurations
RGsB or
Component
Video
S-Video
Composite
Video
RGBS or
RGBcvS
Video
H/HV
V
G
/Y
VID
H
/HV
V
R
/
R-Y
R/
R-Y
B
/C
B-Y
G/Y
VID
B/C
B-Y
H/HV
V
R/
R-Y
G/
Y
VID
B/
C
B-Y
H/HV
V
R/
R-Y
G/Y
VID
B
/C
B-Y
H/
HV
V
R
/
R-Y
G
/Y
VID
B
/C
B-Y
Component Video
VID
/
Y
R-Y
B-Y
/C
5
S-Video
VID
/
Y
R-Y
B-Y
/
C
5
Composite Video
VID
/Y
B-Y
/C
5
R-Y
Input 5 Configurations
ISS 506 • Setup Guide (Continued)