Asus P5W64 WS Professional - Manual (Page 58)

2 - 3 2 2 - 3 2 2 - 3 2 2 - 3 2 2 - 3 2 C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n C h a p t e r 2 : H a r d w a r e i n f o r m a t i o n
• These connectors are set to S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E mode by default. In
S S S S S t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, you can connect Serial ATA boot/data hard
disk drives to these connectors. If you intend to create a Serial ATA
RAID set using these connectors, set the C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s
item in the BIOS to [RAID]. See section “4.3.6 IDE Configuration” for
details.
• For RAID 5, use at least three hard disk drives. For RAID 10, use at
least four hard disk drives. Use two to four Serial ATA hard disk
drives for each RAID 0 or RAID 1 set.
3 . 3 . 3 . 3 . 3 . I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] ,
S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] ) S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] ) S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] ) S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
These connectors are for Serial ATA signal cables for Serial ATA hard
disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 10, and RAID 5 configuration with the Intel
® Matrix
Storage Technology through the onboard Intel ® ICH7R RAID controller.
If any device jumper is set as "Cable-Select," make sure all other device
jumpers have the same setting.
Black or gray
D r i v e j u m p e r D r i v e j u m p e r D r i v e j u m p e r D r i v e j u m p e r D r i v e j u m p e r M o d e M o d e M o d e M o d e M o d e C a b l e C a b l e C a b l e C a b l e C a b l e
s e t t i n g s e t t i n g s e t t i n g s e t t i n g s e t t i n g o f d e v i c e ( s ) o f d e v i c e ( s ) o f d e v i c e ( s ) o f d e v i c e ( s ) o f d e v i c e ( s ) c o n n e c t o r c o n n e c t o r c o n n e c t o r c o n n e c t o r c o n n e c t o r
Single device Cable-Select or Master - Black
Two devices Cable-Select Master Black
Slave Gray
Master Master
Slave Slave
P5W64 WS PRO
®
P5W64 WS PRO SATA connectors
SATA1
SATA4 SATA3
SATA2
GND SA
T A_TXP0
SA
T A_TXN0
GND SA
T A_RXN0
SA
T
A_RXP0
GND GND SA
T A_TXP1
SA
T A_TXN1
GND SA
T A_RXN1
SA
T
A_RXP1
GND
GND
SA
T
A_TXP2
SA
T A_TXN2
GND
SA
T A_RXN2
SA
T
A_RXP2
GND GND
SA
T
A_TXP3
SA
T A_TXN3
GND
SA
T A_RXN3
SA
T
A_RXP3
GND