Asus T2-PE1 - Manual (Page 67)

4 - 7 4 - 7 4 - 7 4 - 7 4 - 7 A S U S T 2 - P E 1 A S U S T 2 - P E 1 A S U S T 2 - P E 1 A S U S T 2 - P E 1 A S U S T 2 - P E 1
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack 1 before using Serial ATA hard disk drives.
• When using the connectors in S S S S S tandard IDE t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table below for the recommended SATA hard disk drive
connections.
Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection Serial ATA hard disk drive connection
C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o n n e c t o r C o l o r C o l o r C o l o r C o l o r C o l o r S e t t i n g S e t t i n g S e t t i n g S e t t i n g S e t t i n g U s e U s e U s e U s e U s e
S A T A 1 , S A T A 3 S A T A 1 , S A T A 3 S A T A 1 , S A T A 3 S A T A 1 , S A T A 3 S A T A 1 , S A T A 3 B l a c k B l a c k B l a c k B l a c k B l a c k M a s t e r M a s t e r M a s t e r M a s t e r M a s t e r B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k B o o t d i s k
S A T A 2 , S A T A 4 S A T A 2 , S A T A 4 S A T A 2 , S A T A 4 S A T A 2 , S A T A 4 S A T A 2 , S A T A 4 B l a c k B l a c k B l a c k B l a c k B l a c k S l a v e S l a v e S l a v e S l a v e S l a v e D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k D a t a d i s k
7 . 7 . 7 . 7 . 7 . S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 ) ( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
¤
SATA connectors
SATA2
GND
TXP4
TXN4
GND
RXP4
RXN4
GND
GND
TXP3
TXN3
GND
RXP3
RXN3
GND
SATA1
GND
TXP1
TXN1
GND
RXP1
RXN1
GND
GND
TXP2
TXN2
GND
RXP2
RXN2
GND
SATA4 SATA3