Ilink agg, Connecting to the network and tools, Enabling the ports – Net Optics iLink Agg xStream User Manual
Page 2: Check the installation, Configuring the ilink agg xstream, Set the ip address by typing

After the initial set up of the IP address through the local CLI,
connect the Management port with a CAT 5e cable to a switch
or hub. You can access the
iLink Agg xStream CLI remotely
by SSH or access iLink Agg xStream’s web interface through
the browser. The default username is
admin, the password is
netoptics (or use your most updated password).
Connecting to the Network and Tools
Note: SFP+ and SFP modules may be shipped separately. An
appropriate cable is shipped with each module.
To connect iLink Agg xStream to your network or monitoring
tools:
1. Remove the temporary plug from any SFP+ slot and insert
the SFP+ or SFP module until it clicks into place.
2. Plug the cable supplied with the module into the port.
3. Plug the other end of the cable into a network port, Tap, or
monitoring tool.
Enabling the Ports
iLink Agg xStream ships with all ports enabled and each
port speed set to
auto. When a port speed is set to auto, the
speed is automatically configured to match the speed of the
connected SFP. When you connect an SFP with 1G speed,
port auto-negotiation is enabled. You can configure the ports
individually by using the
port CLI command. For example,
configure ports 5 and 7 to 1G by typing
port 5,7 speed 1000,
where 5 and 7 are the ports with 1G SFP modules installed.
Note: Only 1000 and 10000 Mbps speed SFP transceivers are
supported
.
Check the Installation
After you have connected the iLink Agg xStream, verify that
it is functioning correctly by checking the link LEDs for each
of the connected ports. The link LEDs should be illuminated to
indicate that the links are connected and traffic is present.
For more information, see the xStream Family User Guide and
xStream Family CLI Reference on the CD that is included with
the device.
If you have questions, the Net Optics technical support
team is available from 7:00 to 17:30 Pacific Time, Monday
through Friday at (408) 737-7777 and through e-mail at
[email protected]. You can also find information at
www.netoptics.com.
© 2013 by Net Optics, Inc. Net Optics® is a registered trademark of Net Optics, Inc. iLink Agg xStream
TM
is a trademark of Net Optics, Inc.
Configuring the ILink Agg xStream
The iLink Agg xStream is shipped with a default Management
port IP address. If you prepare your network to accept the
default address, you can connect the device to your network
and log into ILink Agg xStream using the default address.
IP:
10.60.4.180
Gateway:
10.0.0.1
Netmask:
255.0.0.0
If you want to assign the device a new IP address, you can
connect a terminal to the iLink Agg xStream console port, log
in, and assign a different IP address.
To get started, access the Command Line Interface:
1. Connect a PC with terminal emulation software to the ILink
Agg xStream console port with the supplied DB9 to RJ45
console cable.
2. Launch the terminal emulation software such as
HyperTerminal or minicom and set the communication
parameters to 115200 baud, 8 data bits, no parity, 1 stop bit,
no flow control.
3. At the login prompt, type
admin, and at the password prompt,
type
netoptics.
4. At the CLI prompt, type
config to go into configuration mode.
5. Change the password for the admin account:
netoptics (config) #>
passwd set password
reenterPassword
where
netoptics (config) #>
commit
6. Set the IP address by typing:
netoptics (config) #> device sysIp ipSet address
netMask
where
gateway.
7. Confirm with a ‘
yes’. The ILink Agg xStream appliance takes
on the new address immediately.
For more information on the CLI, type
help to display command
information, or see the CLI Reference. You can use the tab key
to autocomplete partially typed commands. Entering ? following
a command (and a space) displays the arguments for that
command. The up- and down-arrow keys access the CLI com-
mand history buffer.
iLink Agg
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Console
Management
To Switch Span port, Tap, or monitoring port
SFP+ or SFP module
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
Console
Management
Computer with terminal
emulation software
DB9 to RJ45
console cable