Net Optics iLink Agg Link Aggregator Tap - Manual

2. Launch terminal emulation software such as
HyperTerminal or minicom with the following settings:
115200 baud, 8 data bits, no parity, 1 stop bit, no
ÀRZFRQWURO
3. Connect power to iLink Agg.
Make sure that you connect the power supplies to
two separate, independent power sources.
4. At the login prompt, type admin;; at the password
prompt, type QHWRSWLFV.
5. Change the password for the admin account. Type:
XVHUPRGQDPH DGPLQSULY SZ
where is the new password
6. Set the iLink Agg IP address. Type:
sysip set ipaddr= mask=
gw=
V\VLSFRPPLW
where is the IP address for iLink Agg,
is the netmask, and is the IP
address of the gateway
7. For more information on the CLI, type +HOSto display
command information, or see the User Guide. The
tab key or space bar can be used to autocomplete
partially typed commands. Entering ? following a
command (and a space) displays the arguments for
that command. The up-­ and down-­arrow keys access
the CLI command history buffer.
The CLI can now be accessed remotely by SSH over the
iLink Agg Management port. Connect the Management
port (the top RJ45 on the rear panel) with a CAT5 cable
to a switch or hub to access the CLI over the network.
The default SSH username is OLQNDJJ, the password
is QHWRSWLFVand the port is 22. Use the SDVVZG
command to change the SSH password.
Mounting iLink Agg
iLink Agg is designed to mount in a 19-­inch rack,
occupying 1U of height.
Slide the chassis into the rack
and fasten it in place at the front panel ears using
the supplied screws and washers.
Make sure that the
rack is properly grounded.
Quick Install Guide
iLink Agg Link Aggregator Tap
Unpacking and Inspection
Carefully unpack iLink Agg TM and retain materials for
later use.
iLink Agg ships with the following:
‡ (1) the iLink Agg device
‡ (2) Power cords (AC model only)
‡ (1) Cisco DB9 to RJ45 console cable, 6 ft., for use
with the CLI
‡ Screws and washers for rack mounting
‡ (1) iLink Agg Quick Install Guide (this sheet)
‡ (1) CD containing the iLink Agg User Guide and the
iLink Agg CLI Command Reference
‡ Service Plan Reference Guide
‡ Registration instruction card
‡ Extended Warranty if purchased
Carefully check the packing slip against parts received.
If any part is missing or damaged, contact Net Optics
Customer Service. (Note: SFP modules are ordered
and shipped separately.)
&RQÀJXULQJL/LQN$JJ
$OOFRQ¿JXUDWLRQRSWLRQVVWDWXVDQGVWDWLVWLFVDUH
accessible from the Command Line Interface (CLI). To
XVHWKH&/,RYHUDUHPRWH66+FRQQHFWLRQ¿UVWVHWWKH
system’s IP address using the local RS232 interface.
7RDFFHVVWKH&RPPDQG/LQH,QWHUIDFH
1. Connect a PC with terminal emulation software to
iLink Agg using the supplied DB9 to RJ45 cable.
Management Port
Console Port
For use with -­48V Only
- +
For use with -­48V Only
- +
Management Port
Console Port
Earth
Ground
-48VDC
Return
-48VDC
Return
Power Source 1
Power Source 2
AC Models
DC Models
Independent Power Sources
PESV1HWZRUN3RUWV5- *LJ0RQLWRU3RUWV6)3
*LJ0RQLWRU3RUWV6)3 *LJ6;RU/;)LEHU1HWZRUN3RUWV/&W\SH
*LJ0RQLWRU3RUWV6)3 *LJ1HWZRUN3RUWV6)3
&RSSHU,QOLQH0RGHOV
)LEHU,QOLQH0RGHOV
6SDQ0RGHOV
© 2012 by Net Optics, Inc. Net Optics® is a registered trademark of Net Optics, Inc. iLink Agg TM is a trademark of Net Optics, Inc.
800-­0128-­001 rev B PUBDIRPQ 3/10
iLink Agg TM