Derale Performance Remote Cooler Install Kit - Manual

15753-InstructionSheet
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
INSTALLATION INSTRUCTIONS
REMOTE COOLER INSTALL KIT
PART # 15753
Please read these instructions completely
before beginning installation
KIT CONTENTS
QTY. DESCRIPTION
1 Sandwich Adapter
1 O-ring
2 1/2” NPT x 1/2” Barb Fittings
10ft 1/2” OEM Spec Hose
4 Hose Clamps
QTY. DESCRIPTION
1 13/16-16 Sleeve Nut
4 1/4-20 x 1” Hex Bolts
8 1/4” Washers
4 1/4-20 Lock Nuts
4 6” Zip Ties
IMPORTANT
In most cases the Factory Oil Filter will work with the
supplied sandwich adapter. In some applications where
the frame or exhaust system interferes with the new
filter depth we recommend using a shorter filter length.
See the chart below for possible filter options.
COOLER LOCATION (COOLER SOLD SEPARATELY)
MOUNTING
Cooler can be mounted anywhere space permits. When selecting the best location
for your vehicle, always consider a location that will deliver the maximum airflow.
1. Holding the cooler in place use a marker to identify the four mounting hole
locations.
2. Using a drill and 9/32” drill bit, drill the four mounting holes in the desired location.
3. Using the 1/4-20 Bolts, Washers & Lock Nuts Included, install cooler.
SLEEVE NUT
Diagram #1
SANDWICH ADAPTER INSTALLATION
The Sandwich Adapter fits between the oil filter and the engine block. Before
removing the oil filter, check the clearance between the bottom of the filter and the
closest vehicle obstruction. If there are none, then proceed with the installation.
Otherwise, the Sandwich Adapter is 2-1/4” Thick, so you will need 2-1/2” more
clearance then stock. If you determine that the stock filter will not fit, refer to the
Filter Chart for alternative filter heights.
Diagram #2
1. Remove the factory oil filter from the vehicle.
2. Take the Sandwich Adapter and the two Hose Barb Fittings provided. Using Teflon Tape or a suitable sealant, screw the Hose
Barb Fittings clockwise into the Sandwich Adapter until snug. (See Diagram #2)
3. Using a wrench tighten the two Hose Barb Fittings.
4. Take the O-ring provided, apply a thin film of oil and install into the O-ring groove on the Sandwich Adapter. (See Diagram #2)
5. Making sure the engine block filter landing is clean from oil and dirt, take the Sleeve Nut, Sandwich Adapter, O-ring, and
install onto engine sliding the Sleeve Nut thru the Sandwich Adapter. Turn sleeve nut clockwise onto the engines filter nipple.
6. Using a torque wrench, torque the Sleeve Nut to 20 ft. lbs.
1. Using the hose and clamps provided, install both ends of the hose onto the Hose Barb Fittings, forming a loop.
2. Take the looped end and route the hose to the oil cooler making sure to stay clear of sharp objects, exhaust systems, etc.
All bends in hose need to have a minimum radius of 5” or the diameter of a small coffee can.
3. Cut and attach hoses to the oil cooler using the provided hose clamps. Secure hoses using zip ties.
1. Before starting the vehicle, check engine oil level and add accordingly.
2. Always check fluid levels on a flat surface.
3. After installation and vehicle has completely warmed up, recheck fluid level and inspect all connections for leaks.
ROUTING HOSES
SYSTEM CHECK
Note:
Warning: Installation of accessories should only be undertaken by those with mechanical knowledge and are familiar with working on
vehicles. Always use eye protection (goggles, safety glasses or shield). Park the vehicle in a well lit area, on level ground and apply the
parking brake. Only work on a cold vehicle that has been sitting overnight, failure to do so will result in severe burns and injury. Before starting
the vehicle, make sure no tools or any other items are left under hood that could interfere with or be drawn into moving parts of the engine.
Failure to follow instructions can lead to severe damage and personal injury.
(See Diagram #2)
FRAM WIX FRAM WIX
THREAD FILTER FRAM FILTER WIX FILTER FRAM FILTER WIX
SIZE HEIGHT P/N HEIGHT P/N HEIGHT P/N HEIGHT P/N
5.25 PH13 5.17 51060 4.06 PH30 4.33 51069 13/16-16
Actual Sandwich
Adapter Not Shown