Derale Performance 16 Row Series 10000 Stack Plate Transmission Cooler Kit - Manual

KIT CONTENTS
QTY. DESCRIPTION
1 Transmission Cooler
1 11/32” X 4’ Hose
4 Hose Clamps
1 Insta-dapt Adapter
2 x 3/8” -6AN Barb
Please read these instructions completely before starting the installation.
13401-13403-InstructionSheet
TOOLS NEEDED
Standard Screw Driver
or 5/16” Nut Driver
Dyke Pliers
Razor Knife
5/8” Open End Wrench
QTY. DESCRIPTION
4 Mounting Rods
4 Mounting Clips
4 Foam Pads
2 -6AN x 7/8”-14 Male Adapter
1x1
INSTALLATION INSTRUCTIONS
TRANSMISSION COOLER
PART # 13401-13403
(Continues on Page 2)
The Transmission Cooler can be mounted in multiple locations on your
vehicle. Reference Diagram # 2 for possible cooler positions. #1 is the
ideal location, #2 is second best and #4 being the last choice.
The Cooler core will flow in either direction, there is no specified inlet or outlet port. Note:
Diagram #2
COOLER INSTALLATION
(See Diagram #3)
1. Identify the 4 Mounting Rods, 4 Mounting Clips and
4 1x1 Foam Pads.
2. One by one, Install the 4 Mounting Rods thru the Transmission
Cooler.
3. Take the 1x1 Foam Pads supplied, peel off the paper lining & slide
them onto the Mounting Rods, sticking them against the
Transmission Cooler.
4. Take the Cooler Assembly with attached looped hose and hold in
the desired location.
5. Install the 4 Mounting Rods thru the Radiator/Condenser core.
Do not use excessive force when pushing the Mounting
Rods through the Radiator/Condenser. Excessive force could
cause damage to the fins and possibly puncture a tube.
6. Take the Mounting Clips supplied, making sure they are in the
correct direction (Derale writing out) install onto the Mounting Rods
and cinch them until the 1x1 Foam Pads are slightly compressed.
7. Cut off any excess Mounting Rods.
Mounting
Warning:
COOLER LOCATION
When selecting the best location for your vehicle, always consider a
location that will deliver the maximum airflow. (See Diagram #2)
PRE-INSTALLATION
1. Identify the two -6AN x 7/8” Male Adapters.
2. Install the fittings onto the cooler with the o-ring side toward the cooler.
Thread sealant is not necessary on o-ring fittings.
3. Using a 1 1/8” Open End Wrench, tighten fittings.
4. Install -6AN x 3/8” Barb Fittings onto the cooler and tighten.
8 ecure in place using the Hose Clamps.
Note:
5. Identify the 11/32” X 4’ Hose and Hose Clamps.
6. Slide one hose clamp on each end of the supplied Hose.
7. Using a dab of oil, lubricate each end of the hose and install hose onto
the cooler inlets forming a loop.
. S
This kit includes an Insta-dapt Adapter fitting for adapting the cooler
line to the radiator. (See Diagram #1)
The Insta-dapt fitting has a 1/2”-20 Male/Female thread and fits most
vehicles with 5/16” transmission cooler lines.
For vehicles that are not compatible with the Insta-dapt Adapter, please
reference Radiator Adapter Fitting Guide included.
IMPORTANT
Insta-dapt Adapter
Diagram #1
Diagram #3
7/8” Open End Wrench
1 1/8” Open End Wrench
Foam Pads
Mounting
Clips
Mounting
Rods
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com