Derale Performance Remote Transmission Cooler Mount Kit for 5__16" Lines - Manual

13020-InstructionSheet
Derale Performance, Los Angeles, CA 800.421.6288 www.derale.com
INSTALLATION INSTRUCTIONS
TRANSMISSION - REMOTE COOLER INSTALL KIT
PART # 13020
KIT CONTENTS
QTY. DESCRIPTION
1 -6AN Male x 3/8” Barb Fitting
1 -6AN Female x 3/8” Barb Fitting
10ft 11/32” OEM Spec Hose
2 5/16” Compression Fitting
2 3/8” NPT Female x
3/8” Barb Fitting
1 Thermostat Switch
1 In-line Thermostat Fitting
QTY. DESCRIPTION
4 Hose Clamp
4 1/4”-20 x 1” Hex Bolt
8 1/4” Washer
4 1/4”-20 Lock Nut
4 6” Zip Ties
1 #10 Blue Ring Terminal
2 Blue Female Connector
1 Blue Wire Tap Connector
COOLER LOCATION (COOLER SOLD SEPARATELY)
COOLER INSTALLATION
The purpose of a remote mount cooler is to be able to mount the cooler away from the front of the vehicle therefore not
blocking airflow to the radiator/condenser. This cooler can be mounted anywhere space permits. Always keep in mind that the
cooler still needs access to airflow to perform at its peak.
1. Hold the Oil Cooler Assembly in the desired location.
2. Using a marker, mark the four hole locations.
3. Using a drill and 9/32” drill bit, drill the four mounting holes.
4. Identify the 1/4”-20 x 1” Bolts, 1/4” Washers & 1/4” Lock Nuts supplied and attach the Oil Cooler Assembly.
(Continues on Page 2)
Please read these instructions completely before starting the installation.
Always use backup wrenches when tightening fittings. The AN
fittings supplied in this kit do not require any thread sealant.
IMPORTANT
IN-LINE THERMOSTAT INSTALLATION
Mounting Location
There are two options for installing the In-Line Thermostat.
1. Cooler inlet installation
2. Hose installation
The recommended location for the In-line Thermostat Fitting is on the INLET
side of the oil cooler, so the oil line that provides the cooler fluid from the
transmission.
Always use two wrenches when tightening the In-line Thermostat
Fitting to the oil cooler; failure to use a back up wrench could cause damage to
the cooler core.
The In-line Thermostat Fitting is provided with a -6AN male and female threads.
a) Attach the In-line Thermostat Fitting onto the INLET fitting on the oil cooler.
b) Using Loctite or suitable sealant, carefully HAND TIGHTEN the
Thermostat Switch clockwise onto the In-line Thermostat .
Do not use a wrench or damage to the Thermostat Switch could occur.
The kit provides two brass fittings that are only used with this option. They are
designed to adapt the AN fittings to hose barbs.
a) Using the -6AN Male x 3/8” Barb Fitting provided, attach the fitting
to the female side of the In-line Thermostat Fitting.
b) Using the -6AN Female x 3/8” Hose Barb Fitting provided, attach the
fitting to the inlet on the cooler.
c) Using the OEM Spec Hose and Hose Clamps provided, cut the hose to
the desired length and attach one end of the hose to the oil cooler inlet
and the other to the In-line Thermostat.
d) Using Loctite or suitable sealant, carefully HAND TIGHTEN ONLY the
Thermostat Switch clockwise onto the In-line Thermostat Fitting.
Do not use a wrench or damage to the Thermostat Switch could occur.
Warning:
Warning:
Warning:
(See Diagram #1)
(See Diagram #2)
ONLY
Fitting
Standard Screw Driver
or 5/16” Nut Driver
9/16” Open End Wrench
5/8” Open End Wrench
11/16” Open End Wrench
3/4” Open End Wrench
7/8” Open End Wrench
7/16” Socket & Ratchet
Teflon Tape
Wire Stipper
Wire Crimper
Razor Knife
Marker
Tubing Cutter
TOOLS NEEDED
Inlet
Diagram #1 Diagram #1
In-Line
Thermostat
Fitting
Diagram #2 Diagram #2
In-Line
Thermostat
Fitting
Thermostat Switch
Hose
Hose Clamps
Thermostat
Switch