GlowShift Elite 10 Color Series 60 PSI Boost Gauge - Manual

Elite 10 Color Series 60 PSI Boost Gauge
For Product Numbers: GS-ET01_60 & GS-EWT01_60
Wire Harness Color Code
Red: 12v Constant (un-switched) Source (+) Black: Vehicle / Engine Ground (-)
White: 12v Ignition (switched) Source (+) Orange: 12v Dimmer (switched) Source (+) (optional)
1. Disconnect the negative battery cable.
2. You can install the electronic boost pressure sensor can be installed 1 of the 2
ways listed below.

Non-Turbo Diesel: Thread and secure the included brass barbed
fitting, with a 1/8 NPT female thread, on to the 1/8 NPT boost pressure
sensor. Next, cut any available boost line and insert the included t-
fitting between the 2 cut pieces of boost line. Insert it accordingly, so
that the intersecting cross piece of the fitting is left to be connected to
the boost hose line. Last, route and connect the boost hose line to the
brass barbed fitting and boost sensor.

Turbo Diesel: Drill and tap the intake manifold to 1/8 th -27 NPT, and
directly install the sensor.

Note: After drilling and tapping your intake manifold, be
sure to use vacuum to safely remove all shavings from the
manifold. You may also remove the top of your intake
manifold before drilling for extra protection against drill
shavings.

Note: If you are installing this gauge into a Dodge Ram,
model years 98 to 12, you can install a boost bolt directly to
your intake manifold. Installing this boost bolt does not
require any drilling or tapping and can be purchased at
GlowShift.com
3. Route the boost sensor wire harness from the back of the gauge (port D)
through the firewall to the engine bay. Next, couple and secure the sensor wire
harness to the boost pressure sensor.

Be sure to use a grommet when routing wires through the firewall to
protect them from stripping and damage.
4. Connect the white wire to a positive 12 volt ignition (switched) source. It may
be connected to the fuse panel, an accessory wire, or any positive 12 volt source
that turns on and off with the ignition switch of the vehicle.

Note: If wiring to an un-fused source, install a 3 amp fuse inline within
20 inches of the sources connection. You may obtain an optional
“expandable circuit” accessory. This component easily fits into your
fuse panel and provides an additional fused power wire for accessories
such as gauges. This is available at GlowShift.com or a local auto parts
store.
5. Connect the
red wire to a positive 12 volt constant (un-switched) source, either
directly to the battery or to a fuse panel on the vehicle.

Note: If wiring to an un-fused source, install a 3 amp fuse inline within
20 inches of the sources connection. You may obtain an optional
“expandable circuit” accessory. This component easily fits into your fuse
panel and provides an additional fused power wire for accessories such as
gauges. This is available at GlowShift.com or a local auto parts store.
6. The Night Time Dimming feature decreases the brightness of the gauge face by
30%. Connect the
orange wire to the 12 volt positive headlamp source. This allows
the mode to be activated when the headlights come on. This step is optional and will
not affect operation of the gauge if it is omitted.
Note: Do not connect the
orange wire to a dimmer wheel. This will cause the
gauge lighting to flicker.
7. Connect the black wire from the gauge, to any good (unpainted) ground
connection. You may also route a wire directly to the negative side of the vehicle’s
battery.
8. Reconnect the negative battery cable.
9. Daisy Chain Feature (Optional): If you are installing more than one Elite 10
Color Gauge, you can use the daisy chain feature to power up to 4 additional gauges.
Simply plug the included daisy chain wire into the gauge that is already powered
(port B); then plug the other end of the wire into the daisy chain port on the next
gauge.