Rainbow Electronics ADC14061 - Manual (Page 7)

DC and Logic Electrical Characteristics
The following specifications apply for AGND = DGND = DGND I/O = 0V, V + = V
A
= V
D
= +5.0V, V
D
I/O = 3.0V or 5.0V,
PD = +5V, V
REF+
= +2.0V, V
REF IN
= AGND, f
CLK
= 2.5 MHz, RS = 25 Ω
, C
L
= 50 pF/pin. After Auto-Cal @ Temperature.
Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
: all other limits T
A
= T
J
= 25˚C(Notes 7, 8, 9)
Symbol Parameter Conditions
Typical
(Note 10)
Limits
(Note 11)
Units
CLOCK, RD, PD Digital Input Characteristics
V
IN(1)
Logical ″ 1 ″ Input Voltage V + = 5.25V 2.0 V(min)
V
IN(0)
Logical ″ 0 ″ Input Voltage V + = 4.75V 0.8 V(max)
I
IN(1)
Logical ″ 1 ″ Input Current V
IN
= 5.0V 5 µA
I
IN(0)
Logical ″ 0 ″ Input Current V
IN
= 0V −5 µA
C
IN
V
IN
Input Capacitance 5 pF
CAL, RESET Digital Input Characteristics
V
IN(1)
Logical ″ 1 ″ Input Voltage V + = 5.25V 3.5 V(min)
V
IN(0)
Logical
″
0
″
Input Voltage V + = 4.75V 1.0 V(max)
I
IN(1)
Logical
″
1
″
Input Current V
IN
= 5.0V 5 µA
I
IN(0)
Logical ″ 0 ″ Input Current V
IN
= 0V −5 µA
C
IN
Input Capacitance 5 pF
D00 - D13 Digital Output Characteristics
V
OUT(1)
Logical ″ 1 ″ Output
Voltage
V
D
I/O = 4.75V, I
OUT
= −360 µA 4.5 V(min)
V
OUT(1)
Logical
″
1
″
Output
Voltage
V
D
I/O = 2.7V, I
OUT
= −360 mA 2.5 V(min)
V
OUT(0)
Logical
″
0
″
Output
Voltage
V
D
I/O = 5.25V, I
OUT
= 1.6 mA 0.4 V(max)
V
D
I/O = 3.3V, I
OUT
= 1.6 µA 0.4 V(max)
I
OZ
TRI-STATE Output
Current V
OUT
= 3V or 5V 100 nA
V
OUT
= 0V −100 nA
+I
SC
Output Short Circuit
Source Current
V
OUT
= 0V, V
D
I/O = 3V −10 mA
−I
SC
Output Short Circuit Sink
Current
V
OUT
= V
D
I/O = 3V 12 mA
Power Supply Characteristics
I
A
Analog Supply Current PD = V
D
I/O 70 85 mA(max)
I
D
Digital Supply Current PD = V
D
I/O 7 8 mA(max)
I
D
I/O
Output Bus Supply
Current
PD = V
D
I/O 1 2 mA(max)
Total Power
Consumption PD = V
D
I/O 390 475 mW(max)
PD = DGND < 2 mW
PSRR
Power Supply Rejection
Ratio 250 mV
PP
DC to 10 MHz riding on V
A
1 ⁄ 2 LSB Error
54 dB
AC Electrical Characteristics
The following specifications apply for AGND = DGND = DGND I/O = 0V, V + = V
A
= V
D
= +5.0V, V
D
I/O = 3.0V or 5.0V,
PD = +5V, V
REF+
= +2.0V, V
REF IN
= AGND, f
CLK
= 2.5 MHz, RS = 25 Ω , C
L
= 50 pF/pin. After Auto-Cal @ Temperature.
Boldface limits apply for T
A
= T
J
= T
MIN
to T
MAX
: all other limits T
A
= T
J
= 25˚C(Notes 7, 8, 9)
Symbol Parameter Conditions
Typical
(Note 10)
Limits
(Note 11)
Units
(Limits)
f
CLK
Conversion Clock (CLOCK)
Frequency 300 kHz(min)
3 2.5 MHz(max)
Conversion Clock Duty Cycle
45
55 %(min)
%(max)
t
CONV
Conversion Latency 13 Clock Cycles
t
EOCL
Falling edge of CLK to falling
edge of EOC
1/(4f
CLK
)
90
130
ns(min)
ns(max)
www.national.com 7