Bosch GAS 35 L AFC Professional - Manual (Page 18)

18 | English
1 609 92A 0D1 | (23.7.13) Bosch Power Tools
Technical Data
Noise Information
Measured sound values determined according to EN 60704.
Typically the A-weighted sound pressure level of the vacuum
cleaner is lower than 70 dB(A). Uncertainty K= 3 dB.
The noise level when working can exceed 80 dB(A).
Wear hearing protection!
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under “Technical data” is in conformity with the fol-
lowing standards or standardization documents: EN 60335
and the directives 2011/65/EU, 2006/42/EC,
2004/108/EC including their amendments.
Technical file (2006/42/EC) at:
Robert Bosch GmbH, PT/ETM9,
D-70745 Leinfelden-Echterdingen
Robert Bosch GmbH, Power Tools Division
D-70745 Leinfelden-Echterdingen
25.07.2013
Assembly
 Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum-hose Holder (see figure A)
– Slide the vacuum-hose holders 5 firmly from above into the
retainers 30 intended for this purpose, until they engage.
Mounting the Vacuum Hose (see figure B)
– Mount the vacuum hose 21 onto the hose connection
piece 2 and turn it in clockwise direction to the stop.
Note: While vacuuming, an electrostatic charge develops in
the vacuum hose and accessories caused through the friction
of the dust, which the operator could experience in the form
of static discharging (dependent on environmental influences
and physical perception).
As a general rule, Bosch recommends using an anti-static vac-
uum hose (accessory), when vacuuming fine dusts and dry
materials.
Mounting VAC Accessories (see figure C)
The vacuum hose 21 is equipped with a clip system, with
which the VAC accessories (tool sleeve 20, elbow 22) can be
connected.
Mounting the Tool Sleeve
– Mount the tool sleeve 20 onto the vacuum hose 21 until
both snap-fasteners 31 of the vacuum hose can be heard
to engage.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Mounting Nozzles and Tubes
– Mount the elbow 22 onto the vacuum hose 21 until both
snap-fasteners 31 of the vacuum hose can be heard to en-
gage.
– Afterwards, mount the desired VAC accessory (floor noz-
zle, crevice nozzle, vacuum tube, etc.) firmly onto the el-
bow 22.
– To disassemble, press both snap-fasteners 31 inward and
pull the components apart.
Inserting/Removing a Disposal Bag or Dust
Bag (Dry Vacuuming) (see figures D1
– D2)
For dry vacuuming, a disposal bag 23 or a dust bag (accesso-
ry) can be used. This makes the disposal of the dust easier.
Wet/dry vacuum cleaner GAS 35 L AFC
Article number
3 601 JC3 ... ... 2.. ... 270
Rated voltage V 220 –240 110
Rated power input W 1200 1000
Frequency Hz 50/60 50/60
Container volume (gross) l 35 35
Net volume (for fluids) l 19 19
Dust bag contents l 19 19
Max. vacuum*
– Vacuum cleaner
– Turbine
hPa
hPa 230
254
211
242
Max. flow rate*
– Vacuum cleaner
– Turbine
l/s
l/s 36
74
31
71
Max. vacuum capacity W 1380 1150
Surface of flat-fold filter m 2 0,615 0,615
Dust category L L
Weight according to
EPTA-Procedure 01/2003
kg 12,2 12,2
Protection class / I / I
Degree of protection IP X4 IP X4
* Measured with a Ø 35 mm and 5 m long vacuum hose
The values given are valid for nominal voltages [U] of 230 V. For lower
voltage and models for specific countries, these values can vary.
Automatic Start/Stop feature*
Rated voltage
max. power
output
min. power
output
EU 220 –240 V 2200 W 100 W
UK 110 V 750 W 100 W
UK/DK 240/230 V 1800 W 100 W
CH 230 V 1100 W 100 W
* Specification of the allowable load of the connected power tool (coun-
try-specific)
Henk Becker
Executive Vice President
Engineering Helmut Heinzelmann
Head of Product Certification
PT/ETM9
OBJ_BUCH-1746-002.book Page 18 Tuesday, July 23, 2013 1:17 PM