Bosch GOP 250 CE Professional User Manual

Page 16

16 | English

2 609 932 802 | (14.2.12)

Bosch Power Tools

Mounting/Replacing the Application Tool/Accessory

(GOP 250 CE)
If required, remove an already mounted application tool/ac-

cessory.
For removing the application tool/accessory, loosen the

screw 7 with the Allen key 8 and remove the application tool/

accessory.
Mount the requested application tool/accessory (e.g. plunge

cut saw blade 6) in such a manner on the tool holder 4 that the

offset faces downward (see illustration on the graphics page;

marking on the application tool/accessory is readable from

above).
Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 4. 12 different positions are possible, each

offset by 30°.
For more intermediate positions, the adapter 9 (accessory)

can be used: Allow the adapter to engage with the smooth

side onto the cams of the tool holder 4 (see illustration on the

graphics page). Position the application tool/accessory onto

the adapter in any position.
Fasten the application tool/accessory with bolt 7. Tighten the

bolt with Allen key 8 until the spring washer of the bolt faces

flush against the application tool/accessory.
f

Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting/Replacing the Application Tool/Accessory

(GOP 300 SCE)
If required, remove an already mounted application tool/

accessory.
For this, open the SDS lever 12 to the stop (not further) and

remove the application tool.
Mount the requested application tool/accessory (e.g. plunge

cut saw blade 6) in such a manner on the tool holder 4 that the

offset faces downward (see illustration on the graphics page;

marking on the application tool/accessory is readable from

above).
Turn the application tool/accessory to a position favourable

for the respective job, and allow it to engage into the cams of

the tool holder 4. 12 different positions are possible, each

offset by 30°.
Close SDS lever 12 so that it faces against the housing of the

power tool.
f

Check the tight seating of the application tool/acces-

sory. Incorrect or not securely fastened application tools/

accessories can come loose during operation and pose a

hazard.

Mounting/Replacing a Sanding Sheet on the Sanding Plate
The sanding plate 10 is fitted with Velcro backing for quick

and easy fastening of sanding sheets with Velcro adhesion.
Before attaching the sanding sheet 11, free the Velcro back-

ing of the sanding plate 10 from any debris by tapping against

it in order to enable optimum adhesion.
Position the sanding sheet 11 flush alongside one edge of the

sanding plate 10, then lay the sanding sheet onto the sanding

plate and press firmly.
To ensure optimum dust extraction, pay attention that the

punched holes in the sanding sheet match with the holes in

the sanding plate.
To remove the sanding sheet 11, grasp it at one of the tips and

pull it off from the sanding plate 10.
You can use all sanding sheets, fleece pads/polishing cloth

pads of the Delta 93 mm series of Bosch accessory program.
Sanding accessories, such as fleece pads/polishing cloth

pads, are attached to the sanding plate in the same manner.

Selecting the Sanding Sheet
Depending on the material to be worked and the required rate of material removal, different sanding sheets are available:

Scraper, flexible* Silicone and other

elastic materials

Base plate for

sanding, series

Delta 93 mm*

Depends on sanding

sheet

Accessory

Material

* Optional accessory; for the complete accessories please see Bosch
accessory programme.

Sanding disc Material

Application

Grain size

– All wooden materials

(e.g., hardwood, soft-

wood, chipboard, build-

ing board)

– Metal materials

For coarse-sanding, e.g. of rough, unplaned beams and

boards

coarse

For face sanding and planing small irregularities

medium

100

120

For finish and fine sanding of wood

fine

180

240

320

400

OBJ_BUCH-1271-004.book Page 16 Tuesday, February 14, 2012 11:38 AM