Candy CMD93W - Manual (Page 3)

segment goes on and when it starts blinking. The filter alarm can be seen when the motor is off and for about 30
seconds. To reset the hour counter, keep the button pressed for 2 seconds while the alarm can be seen.
Controls shown in Fig. 16/17: Switch A: LIGHT; position 0: light off; position 1: light on. Switch B: MOTOR
SPEED: makes it possible to select the motor operating speed; position 0: motor off. C : Motor on light.
Controls shown in Fig. 18: Button A = light switch. Button B = first speed motor ON/OFF switch. Button C =
second speed switch. Button D = third speed switch. E = motor on light.
Controls shown in Fig. 19: Button A: turns the lights on/off; every 30 hours of operation the corresponding
pilot lamp (S) comes on to indicate that the grease filters must be cleaned; every 120 hours of operation the
corresponding pilot lamp (S) flashes to indicate that the grease filters must be cleaned and the charcoal filter replaced.
To restart the hour counter (RESET), hold the button A pressed down for about 1” (while the pilot lamp S is on).
Button B: drives the motor in first speed (the corresponding pilot lamp comes on); when holding it down for about 1”,
the motor cuts out; when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated and
thus the motor stops after 5’ (the pilot lamp flashes). Button C: drives the motor in second speed (the corresponding
pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated
and thus the motor stops after 5’ (the pilot lamp flashes). Button D: drives the motor in third speed (the corresponding
pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated
and thus the motor stops after 5’ (the pilot lamp flashes). Button E: drives the motor in fourth speed (the corresponding
pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on) , the TIMER is activated
and thus the motor stops after 5’ (the pilot lamp flashes).
Pay special attention to the grease filters: if the model purchased has the controls shown in Figure 15: the
grease filters must be cleaned approximately once every 30 hours of operation (when the central segment on the
display goes on or starts blinking). To remove the filters: press inward on the clamps at the handles and pull the
filter downward. Wash out the filter using a neutral soap. Once the cleaned filters are reinstalled, keep button R
(Reset) pressed for two seconds to reset the counter. For further information, see the Controls in Fig. 15 in the
paragraph entitled “Operation”. If the model purchased has the controls shown in Figure 16/17/18: the grease filter
must be cleaned periodically: exactly how often depends on use (at least once every other month). To remove the
filter: push inward on the clamp at the handle and pull the filter downward. Wash out the filter using a neutral soap.
If the model purchased has the controls shown in Figure 19: the grease filters must be cleaned approximately once
every 30 hours of operation (when the light button lamp comes on) - Fig. 19S). To remove the filters: press inward
on the clamps at the handles and pull the filter downward. Wash out the filter using a neutral soap. Once the cleaned
filters are reinstalled, to reset the counter hold the light button pressed down for about 1” (Fig.19A) while the
corresponding pilot lamp (S) is on. For further information, see the Controls in Fig.19 in the paragraph entitled
“Operation”.
Replacing the charcoal filters: for filtering hoods, the charcoal filters must be replaced; remove the filter with
a twisting movement (Fig. 14). If the model purchased has the controls shown in Figure 15, the charcoal filters must
be replaced whenever the central segment of the display starts blinking (i.e. every 120 hours of operation). If the
model purchased has the controls shown in Figure 16/17/18, the charcoal filters must be replaced according to use:
on the average once every 6 months. If the model purchased has the controls shown in Figure 19, the charcoal filters
must be replaced each time the light button (Fig.19S) lamp flashes (i.e. every 120 hours of operation).
Lighting: Depending on the model purchased, see Fig. 20, Fig. 21 or Fig. 22.
Fig.20: to remove the halogen lamps, turn the locknut counter-clockwise. Replace with the same type of lamp.
Fig. 21: to replace the incandescent light bulbs, remove the grease filters so as to be able to access the inside of
the unit; remove the screw securing the light fitting and then, working from inside the hood, push the light fitting pin
towards the inside of the unit. Replace with light bulbs of the same type.
Fig. 22: if your appliance has the same kind of lights as in the figure 21, to replace the incandescent light bulbs open
the grease filter and remove it; replace with light bulbs of the same type.
DEUTSCH
BESCHREIBUNG
Das Gerät kann in Umluftversion und in Abluftversion geliefert werden. In der Umluftversion (Abb. 1) werden die
durch das Gerät geleitete Luft und der Dampf durch Kohlefilter gereinigt und dann über die seitlichen Lüftungsgitter
der Haube wieder in Zirkulation gebracht. ACHTUNG! Beim Einsatz der Umluftversion müssen die Kohlefilter zusammen
mit einem Umluftweiche eingesetzt werden, der in den oberen Rohrabschnitt montiert wird und die Rezirkulation der
Luft und Ableitung in die Umgebung ermöglicht (Abb. 1A). Die Kohlefilter werden nicht mitgeliefert. In der Abluftversion
(Abb.2) werden die Dämpfe und Küchengerüche direkt über eine Evakuationsöfffnung in der Wand oder Decke nach
außen abgezogen. Daher sind keine Kohlefilter notwendig.
INSTALLATION
Vor den Montageoperationen muß/müssen zur leichteren Handhabung des Geräts der/die Fettfilter entfernt werden:
Den Festhalter in der Nähe des Griffs nach innen drücken und den Filter nach unten ziehen (Abb. 3/4).
Montage des Kochlöffelhalters (auf Anfrage): Studieren Sie je nach dem von Ihnen erworbenen Modell Abbildung