3M MP8660 - Manual (Page 31)

TECHNICAL
A–4
t 3M 1997
3M Multimedia Projector MP8660
A–6. Computer (RGB) Signal Connection Modes
The MP8660 projector automatically recognizes the following connection modes.
Scan Frequency
Dot Clock
Synchronization Signal
Mode H-Size Pixel
Number
Horizontal
(kHz)
Vertical
(Hz)
Dot Clock
Frequency
(MHz)
Horizontal
width/polarity
Vertical
width/polarity Computer
2 848 640 x 400 24.83 56.42 21.053 64/– 8/– TEXT 56
3 800 640 x 400 31.47 70.09 25.175 96/– 2/+ TEXT 70
3 800 640 x 350 31.47 70.09 25.175 96/+ 2/– TEXT 70
4 832 640 x 400 37.86 85.08 31.500 32/– 3/+ TEXT 85
4 832 640 x 350 37.86 85.08 31.500 32/+ 3/– TEXT 85
5 800 640 x 480 31.47 59.94 25.175 96/– 2/– VGA 60
6 832 640 x 480 37.86 72.81 31.500 40/– 3/– VGA 72
7 840 640 x 480 37.50 75.00 31.500 64/– 3/– VGA 75
8 832 640 x 480 43.269 85.01 36.000 56/– 3/– VGA 85
9 896 640 x 480 34.98 66.62 31.334 64/– 3/– MAC 13
A 1024 800 x 600 35.16 56.25 36.000 72/ 2/ SVGA 56
B 1056 800 x 600 37.88 60.32 40.000 128/+ 4/+ SVGA 60
C 1040 800 x 600 48.08 72.19 50.000 120/+ 6/+ SVGA 72
D 1056 800 x 600 46.88 75.00 49.500 80/+ 3/+ SVGA 75
E 1048 800 x 600 53.67 85.06 56.250 64/– 3/– SVGA 85
F 1152 832 x 624 49.73 74.55 57.283 64/– 3/– MAC 16
10 1344 1024 x 768 48.365 60.006 65.000 136/– 6/– XGA60
11 1328 1024 x 768 56.476 70.069 75.000 136/– 6/– XGA 70
12 1328 1024 x 768 58.13 71.59 77.200 136/– 3/– XGA 72
13 1312 1024 x 768 60.02 75.029 78.750 96/+ 3/+ XGA 75
14 1312 1024 x 768 48.78 60.00 64.000 96/– 6/– MAC 19A
15 1328 1024 x 768 60.24 74.93 80.000 96/– 3/– MAC 19B
Notes:
1. “Mode” denotes the computer mode determined
by the projector. The number can be read by the
read command through RS-232 interface.
2. Advanced scaling is used for all inputs that are
not 800 x 600.
3. Mode 10 and 140: For XGA, full advanced
scaling (vertical and horizontal) is used.
Modes 11–13 and 14: Only vertical advanced
scaling is used.
4. The synchronization signal widths represent the
number of dots (horizontal) and the number of
lines (vertical).
5. H-size denotes the standard number of dots in
the horizontal period.
6. For the MAC16 and MAC19A/B computers, you
must manually set the MAC MODE to “ON” to
determine the correct modes.
Set the MAC MODE to “OFF” for the following
computer modes:
D MAC16 as SVGA75
D MAC19A as XGA60
D MAC19B as XGA75
See Setup Sub–Menu to set MAC MODE.
7. Computer name (in right column) appears when
you display the TEST SCREEN on the projector.