Yamaha GX-700 - Manual (Page 22)

E-14
Compact disc player operation
Program play
You can program up to 20 tracks in any desired order.
1
When the CD player is stopped, press PROG to prepare for
programming.
* “PROG” (
9
) and “P-01” (
2
) will light up on the display,
and all track numbers on the selected disc (
7
) will
begin flashing.
2
If necessary, select the desired disc by pressing DISC
SKIP.
* Just after you change the disc, the CD player reads the
contents of the newly selected disc for a few seconds.
During this internal operation, if you go on to the next
step, “WAIT” (
2
) appears on the display and your
operation is canceled.
3
Use the numeric buttons to select the desired
track number.
* The selected track number (
1
) and the total play time
of the programmed tracks (
2
) will light up on the
display, and soon it will be replaced by the display of the
next play order (
2
). Programmed track numbers on the
selected disc will stop flashing and light up on the music
calendar (
7
).
* Pressing TIME displays the total play time of the
programmed tracks (
2
) for about 1 second, and then it
is replaced by the display of the next play order (
2
).
4
Repeat steps 2 and 3 to program other tracks.
5
Press / to start the program play.
Notes
● The total time of the programmed tracks will not be
displayed, if track number 16 or higher is programmed.
● Skip ( / ) can be performed during play, but only
within the range of the programmed tracks.
● Search ( / ) can be performed during play to search
all tracks, including unprogrammed tracks.
REC/PAUSE
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 0
TIME PROG R. TIME
C
EDIT
D
PRESET
+ I0
E
MODE REPEAT RANDOM TUNER
DISC SKIP
A B
TUNER CD
1
2 5
TIME
3
DISC 1 DISC 2 DISC 3
DOWN UP
VOLUME
STANDBY/ON
DIRECTION
PROGRAM B.BOOST MUSIC INPUT INPUT
MIN
PTY SELECT PRESET/ TUNING/ BAND A/B/C/D/E
DISC CHANGE OPEN / CLOSE
AUTO/MANUAL
TIMER
MEMORY
TIME ADJ
REC/PAUSE DOLBY NR
HOUR
FREQ PS/PTY/RT/CT
RANDOM MODE– PTY SEEK– START REPEAT TIME
DISPLAY MODE
TIME
5
Display information during programming
Music calendar
Play order Selected disc
Total playing time Selected track number
KK
AM
C HALL
YMERSION
EDIT
PROG
S F REP
VOLUME A B OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
AM
C HALL
YMERSION
EDIT
PROG
S F REP
VOLUME A B OVER 15
1 2 3 4
7 8 9 10
13 14 15
5
11
6
12
TOTAL
TRACK
VCD PBC
TIMER
SLEEP
NOR TEST
PHANTOM
RANDOM TUNER
CD
MD
TAPE
KK
To cancel a programmed sequence
There are several methods as described below.
● Press while the CD player is stopped.
● Open the disc tray.
● Turn this system into the standby mode.
To check (and correct) program data
1. Press PROG when the CD player is stopped.
2. Every time
is pressed, the track numbers and
sequential order of the programmed tracks can be checked
one after another. The display of the track number can be
returned (sequentially in reverse order) by pressing
.
3. If you want to correct the program data, press a numeric
button to select the track to replace the one displayed. The
previously programmed track will be cleared from the
memory and the new one will be programmed.
To complete the correction, press PROG or
/ once
again.