Windsor ISCRUB CSE24 10060250 User Manual
Iscrub
This manual is related to the following products:
Table of contents
Document Outline
- 86037660 - 980228 - Chariot parts.pdf
- 86037660 PARTS COVER AND 5-1
- 86037660 PG 5-2 AND 5-3
- 86037660 PG 5-4 AND 5-5
- 86037660 PG 5-6 AND 5-7
- 86037660 PG 5-8 AND 5-9
- 86037660 PG 5-10 AND 5-11
- NOTE: See “SAFETY LABEL LOCATION” page for safety label information.
- 86037660 PG 5-12 AND 5-13
- 86037660 PG 5-14 AND 5-15
- 86037660 PG 5-16 AND 5-17
- NOTE: Complete platform assembly is available, Part No. 86028310
- 86037660 PG 5-18 AND 5-19
- 86037660 PG 5-20 AND 5-21
- 86037660 PG 5-22 AND 5-23
- 86037660 PG 5-24 AND 5-25
- 86037660 PG 5-26 AND 5-27
- 86037660 PG 5-28 AND 5-29
- 86037660 PG 5-30 AND 5-31
- 86037660 PG 5-32 AND 5-33
- 86037660 PG 5-34 AND 5-35
- 86037660 PG 5-36 AND 5-37
- 86037660 PG 5-38 AND 5-39
- 86037660 PG 5-40 AND 5-41
- 86037660 PG 5-42 AND 5-43
- 86037660 PG 5-44 AND 5-45
- NOTE: Complete Squeegee Assembly available, Part No. 47455
- 86037660 PG 5-46 AND 5-47
- 86037660 PG 5-48 AND 5-49
- 86037660 PG 5-50 AND 5- 51
- 86037660 PG 5-52 AND 5-53
- 86037660 PG 5-54 AND 5-55
- 86037660 PG 5-56 AND 5-57
- 86037660 PG 5-58 AND 5-59
- 86037660 PG 5-60 AND 5-61
- 86037660 PG 5-62 AND 5-63
- 86037660 PG 5-64 AND 5-65
- 86037660 PG 5-66 AND 5-67
- 86037660 PG 5-68 AND 5-69
- 86037660 PG 5-70 AND 5-71
- 86037660 PG 5-72 AND 5-73
- * NOT SHOWN – FOR WET CELL BATTERIES
- * NOT SHOWN – FOR AGM BATTERIES
- 86037660 PG 5-74 AND 5-75
- 86037660 PG 5-76 AND 5-77
- 86037660 PG 5-78 AND 5-79
- 86037660 PG 5-80 AND 5-81
- 86037660 PG 5-82 AND 5-83
- 86037660 PG 5-84 AND 5-85
- 86037660 PG 5-86 AND 5-87
- 86037660 PG 5-88 AND 5-89
- 86037660 OPTIONS COVER AND 6-1
- 86037660 PG 6-2 AND 6-3
- 86037660 PG 6-4 AND 6-5
- 86037660 PG 6-6 AND 6-7
- 86037660 PG 6-8 AND 6-9
- 86037660 PG 6-10 AND 6-11
- 86037660 PG 6-12 AND 6-13
- 86037660 PG 4-30 AND 4-31.pdf
- PROBLEM
- CAUSE
- ERROR CODE
- SOLUTION
- ERROR
- PROBLEM
- LCD display on, but incomplete
- Power down error
- Memory corrupt
- Throttle wiring
- Possible short circuit of motors, auxiliary outputs (headlight, recycle pump, or back-up alarm), wiring or damaged controller
- LCD module communications timeout
- LCD module settings corrupt
- Brush motor or brush circuit fault
- Vacuum motor or vacuum circuit fault
- Traction motor open circuit fault
- Traction motor overcurrent error
- Traction motor in power foldback state
- Emergency stop error
- Brush current requirement not satisfied
- 86037660 PG 4-32 AND 4-33.pdf