Operation, Adat routing, Adat in – TC electronic SDN BHD x32 User Manual
Page 10
OPERATION
8
ADAT Routing
The four ADAT channel pairs can be routed to any pair of
AES+SPDIF+TOS channels and to the eight ADAT
channels simultaneously as well.
Example 2
In the example below the following is selected:
Normal sample rate
ADAT ch. 1-2 is sent to AES+SPDIF+TOS ch. 1-2
ADAT ch. 3-4 is sent to AES+SPDIF+TOS ch. 3-4
ADAT ch. 5-6 is sent to AES+SPDIF+TOS ch. 5-6
ADAT ch. 7-8 is sent to AES+SPDIF+TOS ch. 7-8
All ADAT channels are sent to ADAT out.
ADAT channels 1-2 are sent to the analog monitor and
headphones outputs.
SRC - (Sample Rate Conversion)
Press to activate sample rate conversion on all ADAT
input channels. This will deselect any previously selected
sample rate conversion.
3-4
1-2
5-6
7-8
adat
mon
adat in
aes+spdif+tos
NS
DS
LOCK
SIG
1/2
3/4
5/6
7/8
SRC
1-2
3-4
5-6
7-8
adat
1-8
FORMAT CONVERTER | PATCHBAY | FIREWIRE IO
digitalkonnekt x32
3-4
3-4
3-4
1-2
1-2
1-2
5-6
5-6
5-6
7-8
7-8
7-8
adat
adat
adat
mon
mon
mon
setup/util
scenes
aes/spdif/tos in
adat in
firewire in
master clock
aes+spdif+tos
aes+spdif+tos
aes+spdif+tos
SRC
SPDIF
TOS
NS
1-8
44.1k
clock rate
aes
/spdif
monitor LEDs
dual wire XLR
hold to select input
security
lock device
adat
monitor
+phones
WCK in
firewire
INT
48k
x2
x4
TOS IN 5/6
FRONT
aes/spdif clock master
DS
9-16
LOCK
SIG
LOCK
SIG
LOCK
SIG
SEL
1/2
1/2
1/2
3/4
3/4
3/4
5/6
5/6
5/6
7/8
7/8
7/8
SRC
HOLD TO STORE SCENE
input signal
HOLD TO UN-LOCK
192kHz fs
AES pro out
1
2
3
4
1-2
1-2
1-2
3-4
3-4
3-4
5-6
5-6
5-6
7-8
7-8
7-8
adat
1-8
adat
1-8
adat
1-8
P
3-4
1-2
5-6
7-8
adat
mon
adat in
f
aes+spdif+tos
NS
DS
LOCK
SIG
1/2
3/4
5/6
7/8
SRC
1-2
3-4
5-6
7-8
adat
1-8
ADAT In
This section routes the signal present on the ADAT in
connection. The signal can be routed to AES/EBU,
SPDIF, Toslink and ADAT outputs and any pair of
channels can also be routed to monitor out.
NS & DS - (Normal and Double Sample Rate)
Using these switches you can alternate between using
normal or double sample rate for the ADAT format.
At normal sample rate, 44.1 or 48 kHz, up to eight
channels can be sent on a single lightpipe cable. Use
MAIN 1-2 connections on the rear panel.
At double sample rate, 88.2 or 96kHz, four channels per
lightpipe connection can be sent. To facilitate eight
channels, two lightpipe cables for inputs and 2 lightpipe
cables for outputs must be used.
3-4
3-4
1-2
1-2
TOS
96k
96k
MAIN
MAIN
ADAT
OUT
IN