Toshiba TLP T521E - Manual (Page 28)

Operations
55 54
■
The display setting menu
Use this menu to set screen display-related items.
(Full): Display with LCD panel’s resolution
(Thru): Display with sampling resolution (for computer input)
(Wide): Wide-screen display (for Video, S-video, and Y/P
B /P R )
Select one of the languages below to use for displaying menus and messages
[ : Enter setting mode] [ :Selection] [Apply: ]
English/Français/Deutsch/Italiano/Español/
Português/ / / /
Screen to display when there is no input signal (Logo) (Blue) (None)
Display icons as function guides On Off
Display start-up screen when power turned on On Off
Description Item
Screen size
Language
Background
Icon
Start-up screen
Not displayed with
PC card input or
camera input.
Note
• If “Thru” is selected for screen size, portions exceeding the pixel count of the LCD panel
p.69 will not appear on the screen. Note that for RGB signals with clock speeds UXGA
60 p.70 or lower, all input pixel signals are sampled. (This effect is noticeable when the
screen is enlarged using the Resize function p.31 ). However, if the clock speed is higher
than this, the RGB pixel signal is thinned before sampling.
■ The PC card setting menu (Models equipped with PC card slot)
Use this menu to set PC Card-related items.
● When using a memory PC card
Manual Auto (Switch to PC card input when a PC card is inserted)
Off On (Begin slid show when PC card is inserted)
Select one of the following slide show display intervals:
5 sec./10 sec./30 sec./1 min./3 min./5 min./10 min.
Delete the selected file (Folders cannot be deleted)
[ : Enter execution mode] [Yes No] [Apply: ]
Description Item
Input select mode
Auto. Demo
Interval
File deletion
Using the menus (Continued)
■
The image adjustment menus
Use this menu to adjust image-related items.
Items Items that can be adjusted are marked with “Yes”, and those that cannot are marked
with “No”.
Notes
1: Tint can only be adjusted when Video mode
p.29 is NTSC or NTSC4.43.
2: Up/down shift can only be adjusted when Screen size p.55 is Wide.
■ The default setting menu
This menu shows placement status and other settings.
Set projection mode in accordance with Placement Style
Set the time to wait after signal input stops until turning off the power:
Off (not turned off) 1 min 2 min ... 60 min
Set whether to turn on the power when the ON/STANDBY button is pressed
(Manual), or when the power cord is plugged in (Auto). Manual Auto
Set the lamp power Standard Low
Set standby mode according to functions used Standard Economy
Description Item
Projection
mode
No signal
power off
Power on
Lamp power [Note 1]
Standby mode [Note 2]
(Back hung
from ceiling) (Placed
on floor) (Rear) (Hung from
ceiling)
p.21
Notes
1: When lamp power is set to low, the screen becomes a little darker, but the cooling fan noise gets
quieter. This setting will be cleared when you turn the power off. The setting will be back to
“Standard” when the power is turned on next time.
2: The Standby mode function is only available with models equipped with a PC card slot p.41 .
Notes
• Note that if Power on is set to Auto, then if the power cord is plugged in when power is
restored after a power outage, the projector power will come on.
• Even if Power on is set to Auto, press the ON/STANDBY button to turn off the power.
Unplugging the power cord to cut off the power will shorten the life of the lamp.
Item Description Computer Y/P B /P R
Video
PC Card Camera
S-video
Contrast Lower Higher Yes Yes Yes Yes Yes
Brightness Darker Brighter Yes Yes Yes Yes Yes
Color Lighter Deeper No Yes Yes No No
Tint [Note 1] Reddish Greenish No No Yes No No
Sharpness Softer Sharper No Yes Yes No Yes
R-level Less red More red Yes Yes Yes Yes Yes
G-level Less green More green Yes Yes Yes Yes Yes
B-level Less blue More blue Yes Yes Yes Yes Yes
Up/down shift [Note 2] Shift down Shift up No Yes Yes No No