Part vii sound – Technics sx-PR604/M User Manual
Page 104

SOUND:
Use the SOUND
∧
and
∨
buttons to select a sound.
• The buttons on the control panel may also be used to
select a sound.
VOLUME:
Use the VOLUME
∧
and
∨
buttons to adjust the volume
(0 to 127).
PAN:
Use the PAN
∧
and
∨
buttons to adjust the stereo balance
(L64–CENTER(CTR)-R63).
• At L64, the sound is completely to the left, at R63
completely to the right. At CENTER, the sound is at the
center. The display indicates the selected position.
• Even at the same numerical value, the stereo balance
may differ slightly depending on the sound.
SUSTAIN:
Use the
∧
and
∨
buttons to adjust the length of the sustain
(1–8). Use the ON/OFF buttons to enable or disable the
sustain effect, when the sustain pedal is depressed.
GLIDE PEDAL:
Use the GLIDE ON/OFF buttons to enable or disable the
glide effect, if it has been assigned to the pedal.
• For pedal settings, refer to page 121.
KEY SHIFT:
Use the KEY
∧
and
∨
buttons to specify the amount of
key shift (–24 to +24).
• A value of 1 means a shift of one semi-tone. To raise (or
lower) the pitch one octave, set the value to +12 (or –12).
• The
∨
button is used to lower the pitch, and the
∧
button
to raise the pitch.
TUNING:
Use the TUN
∧
and
∨
buttons to adjust the fine tuning
(–128 to +127).
• The
∨
button is used to lower the pitch, and the
∧
button
to raise the pitch.
ORIGINAL TUNING:
Use the ORIG. ON/OFF button to enable or disable the
tuning for each sound.
• For details about ORIGINAL TUNING, refer to page 107.
REVERB:
Use the REVERB
∧
and
∨
buttons to adjust the depth
of the REVERB (0 to 127).
DIGITAL EFFECT:
Use the DIG. EFFECT ON/OFF buttons to set the DIGI-
TAL EFFECT to on or off.
CHORUS:
Use the ON/OFF button to set the CHORUS to on or off.
Use the
∧
and
∨
buttons to adjust the depth of the effect
(0 to 127).
MULTI:
Use the ON/OFF button to set the MULTI EFFECT to on
or off. Use the
∧
and
∨
buttons to adjust the depth of
the effect (0 to 127).
EQ LOW:
Use the FC, GAIN
∧
and
∨
buttons to adjust the sound
quality in the lower range.
EQ HI:
Use the FC, GAIN
∧
and
∨
buttons to adjust the sound
quality in the upper range.
FILTER RESONANCE:
Use the RESO
∧
and
∨
buttons to adjust the amount of
resonance (0 to 127).
BRIGHTNESS:
Use the BRIGHTNESS
∧
and
∨
buttons to adjust the
brightness of the sound (0 to 127).
ATTACK TIME:
Use the ATTACK
∧
and
∨
buttons to specify the attack
time (0 to 127).
DECAY TIME:
Use the DECAY
∧
and
∨
buttons to specify the decay
time (0 to 127).
RELEASE TIME:
Use the RELEASE
∧
and
∨
buttons to specify the release
time (0 to 127).
VIBRATO RATE:
Use the RATE
∧
and
∨
buttons to specify the vibrato
speed (0 to 127).
VIBRATO DEPTH:
Use the DEPTH
∧
and
∨
buttons to specify the vibrato
depth (0 to 127).
VIBRATO DELAY:
Use the DELAY
∧
and
∨
buttons to specify the time in-
terval from when the keys are played until the vibrato
starts (0 to 127).
•
The center value is 64 (
±0).
So
u
n
d
Part VII
Sound
104
QQTG0665