Toshiba Q9 Series - Manual (Page 7)

Meets or Exceeds
Q9 Standard Specifications
Input Voltage 230 V
HP Rating 1 2 3 5 7.5 10 15 20 25 30 40 50 60
Current Rating 4.8 7.8 11 17.5 25.3 32.2 48.3 62.1 78.2 92 120 150 177
Input Voltage 460 V, 50/60 Hz, Three-Phase
HP Rating 1 2 3 5 7.5 10 15 20 25 30 40 50 60
Current Rating 2.1 3.4 4.8 7.6 11 14 21 27 34 40 52 65 77
HP Rating 75 100 125 150 200 250 300 350 400
Current Rating 96 124 156 180 240 302 361 414 477
Power Requirements
Input Voltage Range 200 to 240 V, 50/60 Hz, Three-Phase 380 to 480 V, 50/60 Hz, Three-Phase
Power Terminals Input (L1/R, L2/S, L3/T), Output (T1/U, T2/V, T3/W), DCL (PO, PA), DC Bus (PA, PC)
Voltage Tolerance ±10%
Frequency Tolerance ±2%
Control Specifications
Output Method Sine Wave Pulse-Width Modulated System
Output Frequency Range 0 to 299 Hz
V/Hz Pattern
Constant Torque, Variable Torque, Automatic Torque Boost, Sensor-Less Vector Control (Speed), V/f Five-Point Setting,
Permanent Magnet Control, Auto Power-Saver
Overload Current Rating 100% Continuous; 110% for One Minute
Frequency Control Rotary Encoder Integrated Into EOI, 0 to 10 VDC, ±10 VDC, 4 to 20 mA, Binary Input, Motor Operated Potentiometer
Frequency Accuracy Analog Input: ±0.2% of Maximum Output Frequency; Digital Input: ±0.01% of ±0.022 Hz of Output Frequency
Frequency Resolution Operation Panel: 0.01 Hz
Acceleration/Deceleration 0.1 to 6000 Seconds
Analog Inputs Three: One Isolated Input Selectable Between 0 to 10 VDC/4 to 20 mA, One 0 to 10 VDC, and One ±10 VDC
Analog Outputs Two Programmable to 57 Functions (One Switchable 0 to 10 VDC/0 to 20 mA, and One 0 to 1 mA)
Discrete Inputs Eight Programmable to 41 Functions
Sink/Source Switching Ability to Switch Between Sink Logic and Source Logic
Discrete Outputs Three Programmable to 83 Functions (Two Form-A and One Form-C); Outputs Rated at 2 A/120 VAC, 2 A/30 VDC
PID (Set Point Control) Adjustment of Proportional Gain, Integral Time, Differential Time, and Delay Filter
Braking Control DC Braking, Over-Flux Braking
Communication Ports Two-Wire/Four-Wire RS485
Communication Protocol BACNet ® , LonWorks ® , Metasys N2 ® , Modbus RTU ® , APOGEE FLN ®
Protection
Protective Functions Overvoltage Stall, Overcurrent Stall, Critical (Skip) Frequencies, Ride-Through, Electronic Thermal Motor Protection
Interrupting Current Rating 100,000 AIC
Faults
Overcurrent, ASD Overheat, ASD Overload, Motor Overload, Overvoltage, Overtorque, Undercurrent, Ground Fault,
Communication Time-Out, Analog-Input Terminal Overvoltage, Emergency Stop, Input/Output Phase Loss, RAM/ROM
Error, Undervoltage
Retry Ability to Reset Certain Faults Automatically; Programmable Up to 10 Retries
Restart Ability to Detect Speed and Direction of Freewheeling Motor and Start into Motor Smoothly
Interface
EOI Display Full-English Backlit LCD Display
Keys LOCAL/REMOTE, ESC, RUN, MODE, STOP/RESET
Rotary Encoder Encoder with Integrated Enter Key for Frequency and Parameter Adjustments
Monitoring Monitors 19 Drive Conditions
Display Units Programmed to Display Percentage or Volts/Amps
Ambient Conditions
Temperature -10˚ to 40˚C
Relative Humidity Maximum 93% (Non-Condensing)
Altitude 1000 Meters or Less
Q9 Dimensions
230 V 1 to 2 HP
3 to
5 HP
7.5 HP 10 HP
15 to
20 HP
25 to
30 HP
-
40 to
60 HP
- 100 HP 125 HP - - -
460 V 1 to 3 HP
5 to
7.5 HP
10 HP
15 to
20 HP
25 to
30 HP
40 HP
50 to
60 HP
-
75 to
125 HP
150 HP 200 HP 250 HP
300 to
350 HP
400 HP
Frame 2 3 4 5A 5B 6 7A 7B 8 9B 10B 11B 12B 13A
Height (in.) 10.0 11.1 12.6 12.6 15.7 16.5 21.7 21.7 24.8 36.2 40.2 46.9 46.9 46.9
Width (in.) 5.1 6.1 6.9 8.3 9.1 9.4 9.4 12.6 12.6 12.2 13.8 13.0 16.9 23.0
Depth (in.) 6.0 6.5 6.5 7.5 7.5 8.3 8.3 9.5 11.4 14.6 14.6 14.6 14.6 14.6
Your Specifications