Troubleshooting —continued – Onkyo TX-NR5007 User Manual
Page 155
155
The surround speakers produce no sound
• When the DTS Surround Sensation, T-D (Theater-
Dimensional), Stereo or Mono listening mode is
selected, the surround speakers produce no sound.
• Depending on the source and current listening mode,
not much sound may be produced by the surround
speakers. Try selecting another listening mode.
• Make sure the speakers are configured correctly
The center speaker produces no sound
• When the DTS Surround Sensation or Stereo listening
mode is selected, the center speaker produces no
sound.
• In the Mono listening mode, only the front speakers
output sound if the “Output Speaker” setting is set to
“Left / Right” (page 100).
• Make sure the speakers are configured correctly
The front high, front wide and surround back
speakers produce no sound
• Depending on the current listening mode, no sound
may be produced by the front high, front wide, and
surround back speakers. Select another listening mode
(page 89).
• Not much sound may be produced by the front high,
front wide, and surround back speakers with some
sources.
• Make sure the speakers are configured correctly
• While Powered Zone 2 is being used, playback in the
main room is reduced to 7.2-channels and the front
high and front wide speakers produce no sound
(page 130).
• While Powered Zone 3 is being used, playback in the
main room is reduced to 7.2-channels and the sur-
round back speakers produce no sound (page 130).
The subwoofer produces no sound
• When you play source material that contains no infor-
mation in the LFE channel, the subwoofer may pro-
duce no sound.
• Make sure the speakers are configured correctly
The Zone 2/3 speakers produce no sound
• The Zone 2/3 speakers only output sources that are
connected to an analog input. Check to see if the
source component is connected to an analog input.
• Powered Zone 2 cannot be used if “Speakers
Type(FrontB)” is set to “Normal”, “Bi-Amp”, or
“BTL” (pages 57 and 131).
• Powered Zone3 cannot be used if “Speakers
Type(FrontA)” or “Speakers Type(FrontB)” is set to
“Bi-Amp” or “BTL” (pages 57 and 133).
There’s no sound with a certain signal format
• Check the digital audio output setting on the con-
nected device. On some game consoles, such as those
that support DVD, the default setting is off.
• With some DVD-Video discs, you need to select an
audio output format from a menu.
• Depending on the input signal, some listening modes
cannot be selected (pages 82 to 88).
Can’t get 6.2/7.2 playback
• If no front high, front wide and surround back speak-
ers are connected, or the Zone 2/3 speakers are being
used, 6.2/7.2 playback is not possible.
• You can not always select all of the listening modes,
depending on the number of the speakers connected
(pages 82 to 88).
The speaker volume cannot be set as required
(The volume cannot be set to +18.0 dB)
• Check to see if a maximum volume has been set
(page 110).
• If the volume level of each individual speaker has been
adjusted to high positive values (page 97), then the
maximum master volume possible may be reduced.
Note that the individual speaker volume levels are set
automatically after Audyssey MultEQ
®
XT Room
Correction and Speaker Setup has been completed
(page 62).
Noise can be heard
• Using cable ties to bundle audio cables with power
cords, speaker cables, and so on may degrade the
audio performance, so don’t do it.
• An audio cable may be picking up interference. Try
repositioning your cables.
The Late Night function doesn’t work
• Make sure the source material is Dolby Digital, Dolby
Digital Plus, and Dolby TrueHD (page 117).
The analog multichannel input doesn’t work
• Check the multichannel input connections (page 37).
• Make sure that the multichannel input is assigned to
the input selector (page 57).
• Make sure that the multichannel input is selected
(page 80).
• Check the audio output settings on your source com-
ponent.
About DTS signals
• When DTS program material ends and the DTS bit-
stream stops, the AV receiver remains in DTS listen-
ing mode and the DTS indicator remains on. This is to
prevent noise when you use the pause, fast forward, or
fast reverse function on your player. If you switch your
player from DTS to PCM, because the AV receiver
does not switch formats immediately, you may not
hear any sound, in which case you should stop your
player for about three seconds, and then resume play-
back.