Onkyo AV Receiver TX-NR818 - Manual (Page 59)

Advanced Operations
En-59
Digital Audio Input
If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPTICAL1” to the “TV/CD” input selector.
Here are the default assignments.
■ BD/DVD, CBL/SAT, STB/DVR, GAME1, GAME2,
PC, TV/CD, PHONO
` COAXIAL1, COAXIAL2, COAXIAL3,
OPTICAL1, OPTICAL2:
Select the input to which the component has been
connected.
` - - - - -:
Select if the component is connected to an analog
audio input.
Note
• When an HDMI IN is assigned to an input selector in
“HDMI Input” ( ➔ page 58 ), the same HDMI IN will be set as
a priority in this assignment. In this case, if you want to use the
coaxial or optical audio input, make the appropriate selection in
the “Audio Selector” (
➔ page 72 ).
• Supported sampling rates for PCM signals (stereo/mono) from a
digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,
20, 24 bit.
• “AUX” is used only for input from the front panel.
Main Menu Speaker Setup
Here you can check the settings made by
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function, or set them manually, which is useful if
you change one of the connected speakers after using
Audyssey MultEQ XT32 Room Correction and Speaker
Setup function.
Speaker Settings
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
“Speakers Type (Front)” setting. For details on speaker
wire connection, see “Bi-amping the Front Speakers”
(
➔ page 16 ). When connecting speakers without
crossover network, you need to change the “Speakers
Type (Front)” setting beforehand. For details on
connection, refer to “Using Speakers Without Crossover
Network” (
➔ page 17 ).
Note
• When bi-amping is used, the AV receiver is able to drive up to 5.1
speakers in the main room.
• Before you change these settings, turn down the volume.
■ Speaker Impedance
` 4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
` 6ohms:
Select if the impedances of all speakers are between 6
and 16 ohms.
■ Speakers Type (Front)
` Normal:
Select this if you’ve connected your front speakers
normally.
` Bi-Amp:
Select this if you’ve bi-amped your front speakers.
` Digital Crossover:
Select this if you’re using speakers without crossover
network.
Tip
• If “Speakers Type (Front)” is set to “Digital Crossover”, a
confirmation screen appears. Select “Next (2-7. Digital
Processing Crossover Network)” to display the screen for
Digital Processing Crossover Network (
➔ page 63 ). Continue
with the settings.
■ Powered Zone 2, Powered Zone 3
` No
` Yes:
Zone 2/3 speakers can be used. (Powered Zone 2/3
enabled).
■ Preout to External Amplifier
` No
` Surr Back, Front High, Front Wide
For 9.1-channel playback, select the channel output by
SB/FH/FW EXT AMP jacks. If you select speakers whose
setting in Speaker Configuration is set to “None”, it will be
automatically switched to “80Hz (THX)”.
Input selector Default assignment
BD/DVD COAXIAL1
CBL/SAT COAXIAL2
STB/DVR COAXIAL3
GAME1 OPTICAL1
GAME2 - - - - -
PC - - - - -
AUX FRONT (Fixed)
TV/CD OPTICAL2
PHONO - - - - -
Speaker Setup
Some of the settings in this section are set automatically
by Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup ( ➔ page 37 ).
If you change these settings, you must run
Audyssey MultEQ XT32 Room Correction and
Speaker Setup again (
➔ page 37 ).
1 2 3 4 5
“Setup”
To be continued