Onkyo AV Receiver TX-NR818 - Manual (Page 52)

Advanced Operations
En-52
Note
*1 • The video preview is not displayed when:
– HDMI IN 5/6/7 is the current HDMI input source, or
– No signal is present on the current input source.
• The video of the currently-selected input is displayed on the
main screen, not on a preview thumbnail.
*2 “Dolby Volume”, “Dynamic EQ” and “Dynamic Volume”
cannot be selected when any of the THX listening modes is
selected, with “Loudness Plus” set to “On” or “Preserve
THX Settings” set to “Yes” (
➔ page 62 ).
*3 When “Dynamic EQ” is set to “On” or “Dynamic Volume”
is set to anything else than “Off”, “Dolby Volume” will be
switched to “Off” (
➔ page 65 ).
*4 • When the “Monitor Out” setting is set to “Sub”, “Video”
cannot be selected ( ➔ page 57 ).
• This setting cannot be used with the NET input selector.
*5 Only when you have selected “Custom” in the “Picture
Mode” (
➔ page 70 ), pressing ENTER allows you to adjust
the following items via the Quick Setup: “Brightness”,
“Contrast”, “Hue” and “Saturation”. Press RETURN to
return to the “Picture Mode” setting.
*6 Depending on the input source and listening mode, not all
channels shown here output the sound.
*7 • This setting is not available in either of the following cases:
– The “Audio TV Out” setting is set to “On” ( ➔ page 75 ).
– “HDMI Control(RIHD)” is set to “On” ( ➔ page 75 ) and
you’re listening through your TV speakers.
You can change various audio settings from the Quick
Setup (
➔ page 51 ).
Note
• These settings are not available in either of the following cases:
– The “Audio TV Out” setting is set to “On” ( ➔ page 75 ).
– “HDMI Control(RIHD)” is set to “On” ( ➔ page 75 ) and
you’re listening through your TV speakers.
Sound Program
■ Sound Program
` Stereo Source 1, Stereo Source 2, Stereo Source 3,
Multich Source 1, Multich Source 2, Multich
Source 3
` Off
With this setting, you can select the combination of
settings that you registered in “Sound Program Edit”
(
➔ page 66 ).
Note
• If the input selector is changed, the “Sound Program” setting is
switched back to “Off”.
Tone Control
■ Bass
` –10dB to 0dB to +10dB in 2 dB steps
You can boost or cut low-frequency sounds output
from the front speakers.
■ Treble
` –10dB to 0dB to +10dB in 2 dB steps
You can boost or cut high-frequency sounds output
from the front speakers.
You can adjust the bass and treble for the front speakers,
except when the Direct, Pure Audio or THX listening
mode is selected.
Operating on the AV receiver
Speaker Levels
■ Subwoofer Level
` –15.0dB to 0.0dB to +12.0dB in 0.5 dB steps
■ Center Level
` –12.0dB to 0.0dB to +12.0dB in 0.5 dB steps
You can adjust the volume of each speaker while listening
to an input source.
These temporary adjustments are cancelled when the AV
receiver is set to standby. To save the setting you made
here, go to “Level Calibration” (
➔ page 61 ) before
setting the AV receiver to standby.
Note
• You cannot use these function while the AV receiver is muted.
• These settings cannot be used while a pair of headphones is
connected.
• Speakers that are set to “No” or “None” in “Speaker
Configuration” ( ➔ page 60 ) cannot be adjusted.
• When “Sound Program” is enabled, “Subwoofer Level” cannot
be used if the “Subwoofer” setting is set to “No” in “Sound
Program Edit”.
Using the Audio Settings of Quick
Setup
1 Press TONE repeatedly to select either “Bass” or
“Treble”.
2 Use – and + to adjust.