Onkyo TX-DS595 - Manual (Page 16)

16
STANDBY/ON
STANDBY
OFF ON
POWER
MASTER VOLUME
BASS TREBLE
AV RECEIVER TX-DS 595
PHONES FM AM PHONO C D TAPE
CH LEVEL
VIDEO 2 VIDEO 3 VIDEO 1 DVD
VCR
TUNING PRESET SMART SCAN NAVIGATOR PRESET MEMORY FM MODE DISPLAY RT / PTY/ TP
PUSH TO ENTER
DSP / MODE ADJ SETUP
RETURN
A B SPEAKERS
AUDIO SELECTOR
POWER
STANDBY/ON
AUDIO
OPEN / CLOSE
MUTING
ANGLE SUBTITLE
-- / ---
TV / VCR LEVEL
ENTER
HOME THEATER CONTROLLER RC-447M
STEREO
SURR A.ST
SP B Re-EQ
DIMMER ZONE 2
DIRECT DSP
DSP
SP A
DISPLAY
RANDOM
REC
PREP ROGRA MMED & LEARNING CAPABILIT Y
MODE
INPUT SELECTOR
SEND / LEARN
MACRO
DVD
V 3 V 4 TUN
T 1
C D
V 2 V 1
SA T
STDBY ON
SLE EP
M D
VCR
TV CAB LE
VOL C H
CH SEL TO P ME NU MEN U TES T
MOD E
RC VR C D DVD DIR ECT
DISC
P H
T 2
RE TU RN SETU P
SEARCH
1 2 3
4 5 6
7 8 9
+10 0
ON
RCVR MODE
STDBY
Connecting the power
Turning the power on from the remote controller:
Before you can use the remote controller, you must perform steps 1
and 2 above and place the TX-DS595 in the standby state.
1. Press the RCVR MODE button.
The RCVR MODE button lights green.
2. Press the ON button to turn on the
TX-DS595 (take it out of the standby
state).
To return the TX-DS595 to the standby
state, press the STDBY button.
• The TX-DS595 is shipped with the main power (POWER)
switch in the on position ( ON ). When the power cord is
plugged in for the first time, the TX-DS595 will automatically
enter the standby state and the STANDBY indicator will light
(same condition after step 2 below).
• Before you plug in the TX-DS595, confirm that all connections
have been made properly.
• Turning on the power may cause a momentary power surge,
which might interfere with other electrical equipment on the
same circuit, such as computers. If this happens, use a wall outlet
on a different circuit.
1. Plug the power cord into an AC wall outlet.
2. Press the POWER switch to set the
TX-DS595 to standby state.
The STANDBY indicator will light up.
3. Press the STANDBY/ON button to
turn on the TX-DS595. The display
and four jog dial indicators will light
up and the STANDBY indicator will
turn off.
If you press the STANDBY/ON button
again, the receiver returns to Standby mode.
STANDBY indicator
SEND/LEARN
indicator
STANDBY
OFF ON
POWER
STANDBY/ON
STANDBY
Turn off
To change the display of the input source from TAPE to
MD:
If you connected an MD recorder to the TAPE jack on the TX-
DS595, you can have “MD” appear when the TAPE source button is
pressed. By changing the display, if an Onkyo MD recorder z-
connected, the z system functions will become enabled.
Changing the display:
Press and hold down the TAPE source button until the display
changes from TAPE to MD (approx. 3 seconds).
To return the display to its original setting, perform the same
procedure. This setting is necessary to allow z system functions
for the connected cassette tape or MD recorder.
TAPE
Memory preservation
This unit does not require memory preservation batteries. A built-
in memory power backup system preserves the contents of the
memory during power failures and even when the POWER
switch is set to off. The POWER switch must be set to on in order
to charge the backup system.
The memory preservation period after the unit has been turned off
varies depending on climate and placement of the unit. On the
average, memory contents are protected over a period of a few
weeks after the last time the unit has been turned off. This period
is shorter when the unit is exposed to a highly humid climate.
To wall outlet