Oregon Scientific Mirror Weather Station MR238 - Manual (Page 5)

5
EN
SENSOR DATA TRANSMISSION
Data is sent from the sensor(s) every 60 seconds. The reception icon shown
indicates the status.
SEARCH FOR SENSOR
To search for the sensor, simultaneously press and hold MEMORY and CHANNEL
for 2 seconds.
NOTE If the sensor is still not found, please check the batteries.
CLOCK AND CALENDAR
This product tracks the time and date based on radio-controlled signals from the
RTGR328N remote sensor, or manual settings that you enter.
RADIO-CONTROLLED CLOCK
The time and date are automatically updated by radio-controlled clock signals
from official time-keeping organizations in Frankfurt (Germany) and Rugby
(England) unless you disable this feature.
Initial reception takes 2-10 minutes and is initiated when you first set up the unit
or whenever you press RESET. Once complete, the reception icon will stop
blinking.
How these signals work together:
NOTE To force a manual search for RF clock reception, press and hold SEARCH
on the sensor for 2 seconds.
TURN RADIO-CONTROLLED CLOCK ON / OFF
If you wish to manually set the clock, you must first disable the radio-controlled
feature.
To disable the radio-controlled feature, press and hold DOWN on the main unit
for 2 seconds.
To enable the radio-controlled feature, press and hold UP for 2 seconds.
NOTE When the feature is disabled, the house icon disappears in the upper left-
hand corner of the VFD display.
SET CLOCK
You only need to do this if you have disabled the radio-controlled clock (or if you
are too far from a RF signal).
1. Press and hold CLOCK for 2 seconds.
2. Select the time zone offset hour (+ / -23 hours), 12 / 24-hour format, hour,
minute, year, date / month format, month, day and display language.
3. Press UP or DOWN to change the setting.
4. Press CLOCK to confirm.
NOTE The language options are (E) English, (F) French, (D) German, (I) Italian,
and (S) Spanish. The language you select determines the weekday display.
SWITCH CLOCK DISPLAY
Press CLOCK to toggle between:
•
Clock with day
• Clock with time-zone offset
ALARMS
This product has 2 alarms.
SET ALARM
1. Select Alarm#1 or Alarm#2 by pressing ALARM once or twice (once to view
Alarm #1, twice to view Alarm#2). The alarm number will show just to the right
of the displayed alarm time.
2. Press and hold ALARM for 2 seconds.
3. Select the hour and minute. Press UP or DOWN to change settings.
4. Press ALARM to confirm.
The Daily Alarm icon will light up when the alarm is set.
ACTIVATE/ DEACTIVATE ALARM
To activate / deactivate the alarm, press ALARM ON / OFF. The alarm icons will
light up when the alarm is set. You can set Alarm#1, Alarm#2 or both alarms
simultaneously.
NOTE When the alarm time is reached, the crescendo alarm will sound for 2
minutes. Press any key to silence the alarm. It will sound at the same time the next
day.
SNOOZE
Tap on the area at front of the ACTIVE / SNOOZE panel to temporarily disable
the alarm for 8 minutes.
NOTE The ACTIVE / SNOOZE touch panel is subject to varying degrees of
sensitivity; you may need to tap against the area of the touch panel more than
once and with varying degrees of pressure or force to trigger the function.
ICON DESCRIPTION
Main unit is searching for sensors.
At least 1 channel has been found.
Sensor 1 is sending data. (The number shows which
sensor is selected).
--- The selected sensor cannot be found. Search for the
sensor or check batteries.
ICON MEANING
The unit has contact with the sensor and has synchronized
the time.
The unit has contact with the sensor but the time has not
been synchronized.
The unit has lost contact with the remote sensor but the
time is synchronized.
The unit has lost contact with the remote sensor and the
time is not synchronized.
The unit cannot reach the remote sensor.