beautypg.com

Speaker setup, 45 ). if you use, See “subwoofer input sensitivity – Onkyo TX-NR808 User Manual

Page 45: Setting, Iority in the “digital audio input

background image

45

En

Digital Audio Input

If you connect a component to a digital audio input, you
must assign that input to an input selector. For example, if
you connect your CD player to the OPTICAL IN 1, you
must assign “OPT1” to the “TV/CD” input selector.
Here are the default assignments.

BD/DVD, VCR/DVR, CBL/SAT, GAME, PC,
TV/CD, PHONO, PORT

`

COAX1, COAX2, COAX3, OPT1, OPT2:

Select a corresponding digital audio input that the
component has been connected.

`

- - - - -:

Select if the component is connected to an analog
audio input.

• “AUX” is used only for input from the front panel.

Note

• When an HDMI IN is assigned to an input selector in “HDMI

Input” (

43), the same HDMI IN will be set as a priority in this

assignment. In this case, if you want to use the coaxial or optical
audio input, make the selection in the Audio Selector in the
Home menu.

• Available sampling rate for PCM signals from a digital input

(optical and coaxial) is 32/44.1/48/88.2/96 kHz/16, 20, 24 bit.

• If you connect a component (such as UP-A1 Dock that seated

iPod) to the UNIVERSAL PORT jack, you cannot assign any
input to “PORT” selector.

Analog Audio Input

Some DVD players output the LFE channel from their
analog subwoofer output at 15 dB higher than normal.
With this setting, you can change the AV receiver’s sub-
woofer sensitivity to match your DVD player.

Subwoofer Input Sensitivity

`

0dB

to 15dB in 5 dB step.

Note

• This setting only affects signals connected to the AV receiver’s

multichannel input SUBWOOFER jack.

• If you find that your subwoofer is too loud, try the 10 dB or

15 dB setting.

Main menu

Speaker Setup

Here you can check the settings made by
Audyssey MultEQ Room Correction and Speaker Setup
function, or set them manually, which is useful if you
change one of the connected speakers after using
Audyssey MultEQ Room Correction and Speaker Setup
function.

Note

• These settings are disabled when:

– a pair of headphones is connected, or
– the “Audio TV Out” setting is set to “On” (

56) and an

input selector other than HDMI is selected.

Speaker Settings

If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
Speakers Type(Front)” setting (

45).

For hookup information, see “Bi-amping the Front Speak-
ers” (

15).

Note

• When bi-amping is used, the AV receiver is able to drive up to

5.1 speakers in the main room.

• Before you change these settings, turn down the volume.

Speaker Impedance

`

4ohms:

Select if the impedance of any speaker is 4 ohms or
more but less than 6.

`

6ohms:

Select if the impedances of all speakers are between
6 and 16 ohms.

Speakers Type(Front)

`

Normal

:

Select this if you’ve connected your front speakers
normally.

`

Bi-Amp:

Select this if you’ve bi-amped your front speakers.

Note

• Powered Zone 2 cannot be used if “Speakers Type(Front)” is

set to “Bi-Amp” (

71).

Powered Zone 2

See “Setting the Powered Zone 2” (

71).

Input selector

Default assignment

BD/DVD

COAX1

VCR/DVR

COAX2

CBL/SAT

COAX3

GAME

OPT1

PC

- - - - -

AUX

FRONT (Fixed)

TUNER

- - - - - (Fixed)

TV/CD

OPT2

PHONO

- - - - -

PORT

- - - - -

Speaker Setup

Some of the settings in this section are set automatically
by Audyssey MultEQ

®

Room Correction and Speaker

Setup function (

28).

If you change these settings, you must run
Audyssey MultEQ Room Correction and Speaker
Setup again (

28).