Radio Shack 2.4 GHz Digital Spread Spectrum Cordless Telephone with Caller ID/Call Waiting Deluxe - Manual (Page 14)

14 Operation
ˆ
Operation
A QUICK LOOK AT YOUR PHONE
SELECT/CH — Normally the phone
selects a clear channel. If a call
seems to disconnect for no reason,
press
SELECT/CH on the handset
to select a different channel.
IYWd# IYWd# IYWd# IYWd#
d_d] d_d] d_d] d_d]
appears as your phone search-
es for a clear channel.
VOL
8 8 8 8
/
9 9 9 9####
— To adjust the handset’s
volume during a call, press VOL / CID
8 8 8 8
or
9 9 9 9
to select
LLLLebkc[ ebkc[ ebkc[ ebkc[ CWn_ckc CWn_ckc CWn_ckc CWn_ckc
,
Lebkc[ Lebkc[ Lebkc[ Lebkc[ >_]^ >_]^ >_]^ >_]^
,
Lebkc[ Lebkc[ Lebkc[ Lebkc[ C[Z_kc C[Z_kc C[Z_kc C[Z_kc
, or
Leb# Leb# Leb# Leb#
kc[ kc[ kc[ kc[ Bem Bem Bem Bem
.
The phone maintains the setting even af-
ter you hang up the phone.
Note: When you press
VOL/CID
8 8 8 8
while the volume is maximum or VOL/
CID
9 9 9 9
while the volume is low, the
handset beeps three times and the set-
ting does not change.
FLASH — FLASH performs
the electronic equivalent of a
switchhook operation for spe-
cial services, such as Call
Waiting.
For example, if you have Call
Waiting, press
FLASH to an-
swer an incoming call without
disconnecting the current call.
Press
FLASH again to return
to the first call.
Note: If you do not have any
special phone services, press-
ing
FLASH might disconnect
the current call.
TALK — To make a call, lift the hand-
set and press TALK .
JWba JWba JWba JWba
and the
current volume setting appear, and
the CHARGE/IN USE indicator on the
base lights. Then enter the number.
The number appears as you dial,
then (after a few seconds) the call’s
elapsed time appears.
You can also enter the number be-
fore pressing
TALK . If you make a
mistake, press DEL until the incor-
rect entry is erased, then enter the
correct number. To delete the entire
number, hold down
DEL for at .least
2 seconds. When the number on the
display is correct, press TALK.
JWba JWba JWba JWba
and the current volume setting ap-
pear, and the CHARGE/IN USE indi-
cator on the base lights. The number
you entered and the call’s elapsed
time appear.
When you receive a call,
?dYec_d] ?dYec_d] ?dYec_d] ?dYec_d]
9Wbb 9Wbb 9Wbb 9Wbb
appears. To answer it, lift the
handset from the base and press
TALK . If auto talk is on, just lift the
handset from the base. If the handset
is away from the base, press any key.
JWba JWba JWba JWba
and the current volume setting
appear.
To end a call, place the handset on
the base or press
TALK .
REDIAL/PAUSE — You can quickly dial any of the last three
numbers you dialed. Lift the handset and repeatedly press
REDIAL/PAUSE until the number you wish to dial displays.
Then press TALK and the phone dials the number.
Notes:
• You can also press REDIAL/PAUSE after pressing TALK
to dial the last number dialed.
• The redial memory holds up to 32 digits, so you can
redial long-distance as well as local numbers.
• The redial memory also holds pause entries. See “Enter-
ing a Pause” on Page 16.
The handset window has plastic film
on it to protect it during shipment.
Carefully peel off the film before using
your phone for the first time.