Radio Shack PRO-2053 - Manual (Page 35)

35 Trunking Operation
6. Press ENTER for each entry. If you make
a mistake, press CLEAR and enter the
correct size code.
Notes:
• The default setting of the bank is for
Motorola Type II. However, if you set
Type I and you want to return to Type
II, enter 15 at Step 5.
• To confirm the input, repeat Steps 1–
5 and press ENTER . Each time you
press ENTER , you confirm the size
code. If you find an error, press
CLEAR and begin again at Step 1.
7. Press SCAN to start scanning.
Talk Group IDs
There are 10 talk group ID banks and each
ID bank has 5 sub-banks. Each sub-bank
has 20 ID locations. You can program up to
100 talk group IDs in each bank, so you can
program up to 1,000 talk group IDs in 10
banks. When the scanner stops on a trans-
mission in the Motorola, or EDACS mode, it
checks to see if the ID has been stored. In
the closed mode, the scanner only stops on
the transmission and displays its text tag if
you have stored and not locked out the ID. In
the open mode, the scanner always stops on
a transmission, but it displays the ID's text
tag if you have stored the ID.
Storing Talk Group IDs
To store a talk group ID, press TRUNK when
the scanner stops on a voice channel trans-
mission or when a talk group ID is indicated
in the manual mode.
The bottom line indicates where the ID was
entered as
% ý J8M<э 4 % э J8M<э 4 % э J8M<э 4 % э J8M<ý 4V4 V4 V4 V44 4 4 4 and then changes
to
ээээ
% ы4444 % ы4444 % ы4444 % ы4444 . The first X in % ýJ8M<ý4V44 % ýJ8M<ý4V44 % ýJ8M<ý4V44 % ýJ8M<ý4V44 is the
sub-bank number (0–4) in the bank. XX is
the position number of the ID (00–19) in each
sub-bank.
If you press TRUNK and the ID is already
stored, % ýN8JýJ8M<; % ýN8JýJ8M<; % ýN8JýJ8M<; % ýN8JýJ8M<; appears.
Note: When you try to store more than 100
talk group IDs in a bank, ) ) ) ) ap-
pears. Clear some talk group IDs in order to
store new ones (see “Clearing Talk Group
IDs” on Page 37).
Follow these steps to manually store talk
group IDs or to edit a stored ID.
1. Press PROG .
2. Press TRUNK .
3. To select the bank where you want to
store the ID, repeatedly press FUNC
then
8 8 8 8
or
9 9 9 9
until you reach the
desired bank.
4. Press TRUNK repeatedly to select the
sub-bank.
5. Press
8 8 8 8
or
9 9 9 9
to select the location
where you desire to store the ID num-
ber.
7 S0 S4 S0 S4 S0 — — —
Block
Size Code
9 10 11 12 13 14 15 16
8Wdaý&#& 8Wdaý&#& 8Wdaý&#& 8Wdaý&#& ED ED ED ED
?:ýD ?:ýD ?:ýD ?:ýDe$ e$e$ e$ý&& ý&& ý&& ý&&
CEJ0ýded[ CEJ0ýded[ CEJ0ýded[ CEJ0ýded[
First ID location