Programming motorola trunking systems (uhf-lo) – Radio Shack PRO-2053 User Manual
Page 32
32
Trunking Operation
talk group ID decoding method to be
used for the bank.
Notes:
• If you select
*FKý KILEB<;
*FKý KILEB<;
*FKý KILEB<;
*FKý KILEB<;
instead of
)+0
)+0
)+0
)+0
, or
!
!
!
!
, the scanner does not
trunk. Instead,
*FKý KILEB<;ôý ,I *FKý KILEB<;ôý ,I *FKý KILEB<;ôý ,I *FKý KILEB<;ôý ,I DF;< DF;< DF;< DF;< appears. • If you programmed a Motorola Type I or Hybrid system, see “Programming 4. Press PROG to enter the program mode. 5. Enter the desired trunking frequency using the keypad and decimal point then ENTER to store. 6. To enter additional trunking frequencies as subsequent channels in the same PROG or 8 8 8 8 to access the next open channel then enter the fre- quencies. (See “Storing Known Fre- 7. Press SCAN to start scanning. Notes: • If you make an error in the entry pro- cess, press CLEAR as often as needed to erase the incorrect data. • If you enter a frequency that has already been entered, the scanner sounds an LGCôý = LGCôý = LGCôý = LGCôý = and the channel number that has been dupli- CLEAR and enter the correct frequency. If the dual entry is intentional, press ENTER to accept. • You can replace any frequency by selecting the bank and channel, press- PROG and entering the new fre- quency. Programming Motorola Trunking You can program the scanner to receive Note: Base and offset frequencies vary for â8EBýò â8EBýò â8EBýò â8EBýòVò Vò Vò Vт +* +* +* +* % э*+фэтт % э*+фэтт % э*+фэтт % э*+фэтт )+0èýEFE< )+0èýEFE< )+0èýEFE< )+0èýEFE< â8EBýò â8EBýò â8EBýò â8EBýò *FKýKILEB<; *FKýKILEB<; *FKýKILEB<; *FKýKILEB<; ,I ,I ,I ,I ,òòòUôô ,òòòUôô ,òòòUôô ,òòòUôô фц") фц") фц") фц") тфттттт тфттттт тфттттт тфттттт в8EBýòý â8EBýòý â8EBýòý â8EBýòý б?этт б?этт б?этт б?этт Program mode ,òòòUôô ,òòòUôô ,òòòUôô ,òòòUôô фц") фц") фц") фц") кммфпклн кммфпклн кммфпклн кммфпклн в8EBýòý â8EBýòý â8EBýòý â8EBýòý б?этт б?этт б?этт б?этт Frequency ,òòñUôô ,òòñUôô ,òòñUôô ,òòñUôô фц") фц") фц") фц") тфттттт тфттттт тфттттт тфттттт в8EBýòý â8EBýòý â8EBýòý â8EBýòý б?этс б?этс б?этс б?этс Next channel
Fleet Maps” on Page 33.
press
bank, press
quencies into Channels” on Page 15).
error tone and displays
cated. If the dual entry is an error, press
ing
Systems (UHF-Lo)
transmissions in the UHF-Lo band (406-512
MHz) of the Motorola trunking system. You
can receive these transmissions by checking
the trunking system's control channel. You
must program the system's base frequency
and offset frequency to do this.
each type of trunking system. You can get in-
formation about these frequencies for the
trunking system you want to scan using
www.trunkscanner.com, other Internet
sources, or locally published guidebooks.