NEC 42/50PD1 - Manual (Page 50)

50
Appendix
Signal Identification For Raster Preset
VIDEO NTSC*1
VIDEO PAL*1 VIDEO SECAM*1
640 X 240 (15.734kHz/59.94Hz)
768 X 288 (15.557kHz/50.39Hz)
640 X 400 (31.469kHz/70.086Hz)
640 X 480 (31.469kHz/59.94Hz)
640 X 480 (35kHz/66.667Hz)
640 X 480 (37.861kHz/72.809Hz)
640 X 480 (37.5kHz/75Hz)
640 X 480 (43.269kHz/85.008Hz)
640 X 480 (39.375kHz/75Hz)
800 X 600 (35.156kHz/56.25Hz)
800 X 600 (37.879kHz/60.31Hz)
800 X 600 (48.077kHz/72.188Hz)
800 X 600 (46.875kHz/75Hz)
800 X 600 (53.674kHz/85.061Hz)
832 X 624 (49.725kHz/74.55Hz)
852 X 480 (31.722kHz/59.966Hz)
848 X 480 (31.02kHz/60Hz)
1024 X 768 (56.476kHz/70.069Hz)
1024 X 768 (60.023kHz/75.029Hz)
1024 X 768 (68.677kHz/84.997Hz)
1024 X 768 (60.24kHz/74.93Hz)
768 X 576 (31.389kHz/50Hz)
640 X 480 (31.47kHz/59.9Hz)
VU-6010 NTSC*2
VU-6010 PAL*2
IBM 400@70Hz*3
VESA 480@60Hz
MAC @13''*6
VESA 480@72Hz
VESA 480@75Hz
VESA 480@85Hz*4
XGA-2 480@75Hz
VESA 600@56Hz
VESA 600@60Hz
VESA 600@72Hz
VESA 600@75Hz
VESA 600@85Hz*4
MAC @16''*6
I/O data wide*5
VGA WIDE (NEC1)
VESA 768@70Hz
VESA 768@75Hz
VESA 768@85Hz*4
MAC @19''*6
IDC-3000G PAL625P
IDC-3000G NTSC 525P
-
-
-
-
-
STILL
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
MOTION
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙ ⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
⅙
Factory
settings
User
settings
RGB
MODE
-
-
NORMAL
-
-
NORMAL
-
-
-
-
-
-
-
-
-
-
-
WIDE
-
-
-
-
-
-
NORMAL
MODE*7
-
-
NEG
NEG
NEG
NEG
POS/NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
POS/NEG
NEG
POS
NEG
POS
POS
POS/NEG
NEG
NEG
-
-
NEG
NEG
NEG
NEG
NEG
NEG
POS
NEG
POS
POS
POS
POS
POS
NEG
POS
NEG
POS
POS
NEG
NEG
Y
Y
Y
Y
Y/N
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y/N
Y
Y
Y
Y
Y
Y/N
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
Y
Y
Y
Sync polarity
Ver Hor Ver Hor
*1 Convert to 640 dots x 480 lines and display.
*2 These signals cannot be displayed in the RGB3 input mode.
*3 Display only 400 lines with the screen center of the vertical orientation located at the center.
*4 The picture will be shaky when the moving images of video games, etc., are input. (In this case set the refresh rate to 75 kHz or less.)
*5 Only when using an I/O DATA graphic accelerator board.
*6 Use a separately sold signal adapter (mini D-Sub 15-pin) when connecting to a Macintosh computer.
For some models, make the mini D-Sub 15-pin connection using the included RGB signal cable.
*7 Make the settings to display these signals. The signals will not be displayed properly unless the correct settings are made.
*The resolution deteriorates in comparison with the original image because the image of 640 dots x 480 lines is converted to 853 dots x 480 lines and displayed.
*At the time of video input, video signals derived from poor recording conditions may give rise to a disturbed screen image.
*The sync may be disturbed when non standard signals other than the aforementioned are input.
*Multiple screens (2 screens) can only display signals having an aspect ratio of 4:3. *3 Cannot be used with multiple screens.
*With digital inputs some signals are not accepted.
*852 dot by 480 line signals are displayed with this resolution.
*848 dot by 480 line signals are displayed at a resolution of 848 dots by 480 lines when “NORMAL” is selected, and converted to 853 dots by 480 lines when “FULL” is selected.
Resolution
(horizontal frequency/vertical frequency)
Presence/absence of sync