Philips Epic 51PW9303 - Manual (Page 9)

9
PIP ON/OFF
2 1 3
5 4 6
8 7 9
0
TV
SWAP PIP CH
DN UP
ACTIVE
CONTROL FREEZE
SOUND
MUTE
SURF A/CH
POWER
PICTURE
STATUS/
EXIT
SURF
ITR/
RECORD
HOME
VIDEO HOME
MOVIES
PERSONAL
SLEEP REC •
PIP POSITION
VCR ACC
MENU/
SELECT
VOL CH
TV/VCR
FORMAT
SAP
PROG.LIST DOLBY V AV
5
AV1
VIDEO
S-VIDEO
L Pb
Pr
VIDEO
S-VIDEO
L
AUDIO
L
R
AUDIO
L
R
G/Y
R/Pr
B/Pb
V
H
SYNC
L
R
AUDIO
HD INPUT-AV 4
INPUT-AV 2 OUTPUT INPUT-AV 1 ANTENNA IN 75 Ω
Y
Rear of TV
L
R
AUDIO
HD INPUT-AV 5
DVI
Coaxial Cable
Lead-in from
Cable TV Company
or VHF/UHF Antenna
* (Example: Philips VCR
model VR674CAT)
2
Rear of VCR*
AUDIO
ANT
IN
OUT
VIDEO
L
R
OUT IN CH3 CH4
IN
3
4
1
Connecting Accessory Devices to Your TV
C
ONNECTING A
VCR
T he TV’s audio/video (AV) input jacks provide
for direct picture and sound connections
between the TV and accessory devices such as
VCRs, DVD players, and others that have AV out-
put jacks.
This example, which uses the INPUT-AV 1 jacks,
shows you one way you can connect a VCR to
your TV.
Refer to the directions-for-use manual for your
VCR for further information on connections.
To make the connections shown in this example,
you will need:
• one coaxial cable (75
Ω
)
• one cable for a video connection (standard
RCA-type phono plug)
• two cables for audio connections (standard
RCA-type phono plugs) (only one cable is
needed for a nonstereo VCR).
NOTE: The cables are not supplied with your TV.
You should be able to buy them at most stores
that sell electronics. Or you can call our
Customer Care Center at 1-800-531-0039
1 Connect a cable TV or antenna signal to
the ANT IN jack on the back of the VCR.
2 Connect from the OUT jack on the
back of the VCR to the ANTENNA IN
75
Ω
jack on the back of the TV.
3 Connect the VIDEO OUT jack on the
back of the VCR to the INPUT-AV 2
VIDEO jack on the back of the TV.
4 Connect the audio output R(ight) and
L(eft) jacks on the back of the VCR to
the INPUT-AV 2 AUDIO jacks on the
back of the TV.
NOTE: If the VCR is a mono (nonstereo)
unit, connect only the left audio cable,
which usually has a white-coded plug.
5 Press the AV button on the remote con-
trol as many times as necessary to select
the AV2 source for viewing of materials
from the VCR.
• Stereo sound will pass from the ANT
OUT jack on the VCR to the ANTENNA
IN 75
Ω
jack on the TV only when the
VCR is in TV mode. This is the mode
that allows the TV to use its channel
selector.
• To simplify making connections, audio
and video cables often have color-coded
plugs. The jacks on your TV are likewise
color coded to match the plugs. The cod-
ing is as follows:
—Yellow for video (composite)
—Red for the right audio channel
—White for the left audio channel
NOTE: If your VCR is mono (non-
stereo), you will connect only one audio
cable. You must ensure that the TV is set
to MONO for the signal source to which
you’ve connected the VCR (INPUT-AV 2,
INPUT-AV 1, or the side panel inputs
[AV3]). Otherwise, you will receive
sound from only one of the TV’s speakers.
See page 36.
H
ELPFUL
H
INTS
You can display the AV1, AV2, or AV3 signal
sources in the PIP window. See page 7 of the
Quick Use and Setup Guide for information on
using the Picture-in-Picture (PIP) feature.
c c C
HECK
I
T
O
UT