Panasonic NV-FJ630AM - Manual (Page 17)

17
Recording from an external source
This function can be used to make up an edited tape from
other recordings or video sources.
A new scene can be added to the end of previous one.
POWER JET REW
PIC M
SEARCH TIMER REC
Í / I Á
TAPE REFRESH
I N
OUT
RF OUT IN (AV1)
Preparations
– Connect a video movie camera or another VCR to this VCR
as shown.
– Display the VCR picture on the TV.
– Insert the cassette on which the copying is to be performed,
and make sure that its erasure prevention tab is not broken
out.
– Select the audio source required by pressing the INPUT
SELECT button O to set A1 or A2.
A1: Through the AV1 (AUDIO IN/VIDEO IN)
sockets.
A2: Through the AV2 (AUDIO IN/VIDEO IN)
sockets on front panel.
– Use the L and R connectors for operations in the normal
(monaural) mode.
Recording VCR
AV1 (VIDEO IN ` / AUDIO IN b)
AV2 (VIDEO IN Y / AUDIO IN Z)
Other VCR or
Video movie camera
To Delete all of a Cassette’s Contents
(Tape Refresh Function)
You can delete all of a cassette’s contents (the picture, the
sound and the Jet Navigator data) all at once.
Operations
1
Be sure to set [JET NAVIGATOR] to [ON] when you want
to delete all contents of a cassette that is recorded while
setting [JET NAVIGATOR] to [ON].
Be sure to set [JET NAVIGATOR] to [OFF] when you want
to delete all contents of a cassette that is recorded while
setting [JET NAVIGATOR] to [OFF] or is recorded on
another VCR. (See page 12.)
2 Insert a cassette that you want to delete the cassette’s
contents.
T A P E R E F R E S H
S T A R T : T A P E R E F R E S H
E N D : S T O P
3 Press TAPE REFRESH button [ for
5 seconds or more to put the VCR in
tape refresh standby mode.
4 Press TAPE REFRESH button [ for 2 seconds or more
to start the tape refresh function.
The tape is rewound to the beginning, and it is fast-forwarded
with the tape refresh function.
When the tape reaches the end, the VCR automatically
rewinds it to the beginning.
Note:
– When a video cassette with a broken off erasure prevention
tab is inserted, this function is not activated.
On Screen Display
T A P E R E F R E S H
5
E N D : S T O P
VCR display
Operations
1
Press the Play button 7 to start playback.
2 At the point where you want to join a new scene, press
the Pause/Slow button
J to put it in the still playback
mode.
3 Press the REC button I to put it in the recording pause
mode.
4 Start playback on the source unit and search for the point
from which you want to record (copy) onto this VCR.
5 When that point is reached, press the Pause/Slow button
J again to start recording the new picture and sound from
the playback unit.
6 To record (copy) additional scenes, press the Pause/Slow
button
J to put this VCR in the recording pause mode
and then perform above steps 4 and 5 again.
7 At the point where you want to stop recording, press the
Stop button
F to finish recording.
Notes:
– If you leave the VCR in the recording pause mode for more
than 5 minutes in step 3 or 6, the VCR automatically
switches over to the stop mode to protect the video heads.
– If [DIRECT REC] is set to [ON], connect with AV2 sockets
and select A2.
POWER JET REW
PICTURE MODE
SEARCH TIMER REC
Í / I Á
TAPE REFRESH
(Not supplied)
Other Monaural VCR or
Video movie camera