Philips 107B7 - Manual (Page 15)

17” CDT Color Monitor 107B7
15
A. Press MENU Key to show OSD menu ,and press the down Key to select the "zoom" function, then press
the menu Key to enter second menu, press the down key to select “ “above 10S,then enter into factory
setting area for modulation.
B. Brightness & contrast ratio MAX.
C. Raster Max modulation: Raster Pattern, adjust R or B bias and G2, make x=270 ±10, y=290±10, Y=2.0±0.2
cd/m 2
D. Raster cut off modulation: Raster Pattern, adjust brightness to make Cut off: 0.08±0.02 cd/m 2 ,and then put
9300K & 6500K into it.
E.Small white screen appears, Raster cut off, set SB as 4
(1)Choose 4 for LH ,set R or G or B gain, make x=283 ±15, y=297±15，Y=350±15 cd/m 2 ,then save it into
9300K color temperature, set R or G or B gain, make x=313 ±15, y=329±15, Y=300±15,then save it into 6500K
color temperature, set R or G or B gain, make x=332 ±15, y=347±15, Y=280±15,then save it into 5500K color
temperature, then exit the factory setting area.
(2)Choose 3 for LH,set R or G or B gain, make x=283 ±15, y=297±15，Y=270±15,then save it into 9300K color
temperature; set R or G or B gain, make x=313 ±15, y=329±15,Y=250±15,then save it into 6500K color
temperature, set R or G or B gain, make x=332 ±15, y=347±15, Y=230±15,then save it into 5500K color
temperature, then exit the factory setting area.
(3)Choose 2 for LH,set R or G or B gain, make x=283 ±15, y=297±15，Y=210±15,then save it into 9300K color
temperature; set R or G or B gain, make x=313 ±15, y=329±15,Y=200±15,then save it into 6500K color
temperature, set R or G or B gain, make x=332 ±15, y=347±15, Y=190±15,then save it into 5500K color
temperature, then exit the factory setting area.
(4)Choose 1 for LH,set R or G or B gain, make x=283 ±15, y=297±15，Y=140±15,then save it into 9300K color
temperature; set R or G or B gain, make x=313 ±15, y=329±15,Y=130±15,then save it into 6500K color
temperature, set R or G or B gain, make x=332 ±15, y=347±15, Y=120±15,then save it into 5500K color
temperature, then exit the factory setting area.
F. White screen appears, brightness cut off, set “SB” as 4,adjust AB value, make 9300K color temperature
Y=98 ±1 cd/m 2 ,then save it into 9300K color temperature; set “SB” as 3,adjust AB value, make 9300K color
temperature Y=96 ±1 cd/m 2 ,then save it into 9300K color temperature; set “SB” as 2, adjust AB value, make
9300K color temperature Y=94 ±1 cd/m 2 ,then save it into 9300K color temperature; set “SB” as 1, adjust AB
value, make 9300K color temperature Y=92 ±1 cd/m 2 ,then save it into 9300K color temperature.
G. White screen appears, brightness cut off, set R or G or B gain, make x=313 ±10, y=329±10,Y=80±5 cd/m 2 .
then save it into sRGB color temperature, exit the factory setting area.
H. After modulation, it’s necessary to check if the white balance accords with the normal specification. If not,
needs reset. then exit factory setting area.
4. Focus Adjustment:
A. Set mode7 1024×768@85Hz with character full page.
B. Under the RECALL state.