Pitco Frialator Solstice I12 Water Cooker (Operations Manual) - Manual (Page 6)

Solstice I12 Water Cooker Computer Service
Part #60153301
L20-316 Rev 0 6
Display shows [S hh.mm:ss ] [ NAME nn ] where “ nn ” is the default key number, “ S ” means
Shake, hh. mm:ss” is hour, minutes and seconds .
Use location keys for numeric entry to adjust the current setting. Press the key to save
Shake Time and continue with Hold Time for this product key. A display of [TOO HIGH]
indicates an entry greater than Cook Time. Press the [10/0] key to clear entry, and re-enter a
valid number.
Note: Cook Time minus the time from the beginning of the cook = Shake value to enter.
Example: With a 3:00 cook time and a desired shake alarm at 1 minute into the cook, the value
you enter would be 2:00 minutes. 3:00 – 1:00 = 2:00.
2.2.3 Hold Time
Cooked product may stand in holding bins for a period of time. This timer produces an alarm
to inform operators to discard old product and start a new cook. The Default for this value is
zero, meaning the Hold Time is inactive.
Display is showing [H hh .mm:ss] [Name nn ], where “ nn ” is the default key number, “ H ” means
HOLD, and “ h .mm:ss” is minutes and seconds. Use the location keys for numeric entry to
adjust the current setting. Press the key to save Hold Time and continue with Hold Pre-
Alarm for this product key.
2.2.4 Hold Pre-Alarm
Hold Pre-Alarm is a timer setting that is used to warn operators that the Hold Time is about to
expire. To use Hold Pre-Alarm, time value must be a non-zero value, and must be set to a
value less than Hold Time. The default value is zero, meaning the Hold Pre-Alarm is inactive.
Display is showing [P hh. mm:ss] [Name nn] where “ nn ” is the default key number, P means
Pre-Alarm, and “ hh. mm:ss” is minutes and seconds.
Use the location keys for numeric entry to adjust the current setting.
Press the key to save hold time and continue setup for this product key. A display of
[TOO HIGH] indicates an entry greater than Hold Time. Press the [10/0] key to clear entry, and
re-enter a valid number.
Note: Hold Time minus the time from the beginning of the cook = Hold value to enter.
Example: With a 55:00 hold time and a desired alarm at 35 minutes into the hold period, the
value you enter would be 20:00 minutes. 55:00 – 35:00 = 20:00.
The prior four
steps in table
form:
Press [Clock]
Display shows [SELECT] [PRODUCT]
Press the desired product [Key#]
Display shows [C hh.mm:ss] [NAME nn] C is Cook, nn is key
Enter enter/change desired Cook time.
Display shows [C hh.mm:ss] [NAME nn]
Press [Clock]
Display shows [S hh.mm:ss] [NAME nn] S is Shake, nn is key
Enter enter/change desired Shake time.
Display shows [S hh.mm:ss] [NAME nn]
Press [Clock]
Display shows [H hh.mm:ss] [NAME nn] H is Hold, nn is key
Enter enter/change desired Hold time.
Display shows [H hh.mm:ss] [NAME nn]
Press [Clock] P is Pre-alarm, nn is key
Display shows [H hh.mm:ss] [NAME nn]
Enter enter/change desired HPA time.
Display shows [H hh.mm:ss] [NAME nn]
To Set a Product Key for Cook, Shake, Hold, HPA times,
and Food Safe temperature
P
re
A
la
rm
T
im
e
C
o
o
k
T
im
e
S
h
a
k
e
T
im
e
H
o
ld
T
im
e