Philips FW-V520 - Manual (Page 18)

18
English
3139 115 21093
Select a desired track/passage
To search for a particular passage during
playback
● Press à or á to select 4 different search
speed.
➜ "FRX1"; "FRX2"; "FRX3" or "FRX4" will be
displayed on the TV screen when you select a
fast rewind search.
➜ "FFX1"; "FFX2"; "FFX3" or "FFX4" will be
displayed on the TV screen when you select a
fast forward search.
➜ Normal playback will begin at the end of the
fast rewinding or forwarding of the selected
track.
● Play returns to normal when PLAYÉÅ is
pressed or when a new track is selected.
To select a desired track
● Press í or ë repeatedly (or Digits 0–9 on
the remote control) until the desired track
appears on the display.
● If playback is stopped, press PLAYÉÅ to start
playback.
Note:
– Maximum track selection from digital keys on
the remote control is 199 for MP3-CD and 99 for
VCD/CD.
For MP3-CD only
To select a desired Album
● Press ALBUM - - - - -/+ + + + + (à or á) repeatedly
until the desired Album appears on the display.
➜
ALB will start flashing.
➜ “AXX T001” will be displayed after the
album name scrolled through the display briefly.
To select a desired Title
● Press TITLE - - - - -/+ + + + + (í or ë) repeatedly until
the desired Title appears on the display.
● Use the digital keys on the remote control to
select the track under current Album directly.
➜
TITLE will start flashing.
➜ “A01 TXXX” will be displayed after the title
name scrolled through the display briefly.
Note:
– "
A" represents ALBUM and "T" represents
TRACK, " XX" or "XXX" is the current selected
Album or Track number.
CD/VCD/MP3-CD Operation
Programming the disc tracks
Programming tracks is possible when playback is
stopped. Up to 99 tracks can be stored in the
memory in any order.
1 Load the desired discs on the disc tray (refer to
“Loading Discs”).
2 Press the VCD (CD 1•2•3) button to select the
disc tray.
➜ Programming can only be done on the
selected disc.
3 Press PROG to start programming.
➜
PROG will start flashing.
➜ It will cancel any previously programmed
tracks and selected repeat mode.
4 Press í or ë repeatedly (or Digits 0–9 on
the remote control) to select the desired track.
¶ For MP3-CD, press ALBUM - - - - -/+ + + + + and TITLE
- - - - -/+ + + + + to select the desired Album and Title for
programming.
5 Press PROG to store the track.
¶ Repeat steps 3–5 to store other tracks.
6 Press PLAYÉÅ to start programme playback.
➜ "PLAY PROGRAM" will be displayed.
● To end programming without starting playback,
press Ç once .
➜ The total number of tracks programmed and
the total playing time will appear on the display.
Notes:
– Programme cannot be used for VCDs when PBC
is switched on. Switch off PBC before storing tracks.
– For MP3-CD, total playing time will not be
shown.
– If the total playing time is more than "99:59",
then "--:--" will appear on the display instead
of the total playing time.
– If you attempt to programme more than 99
tracks, "
PROGRAM FULL" will be displayed.
– During programming, if no button is pressed
within 20 seconds, the system will exit the
Programme mode automatically.
To review the programme
● Stop playback and press í or ë repeatedly.
● To exit review mode, press Ç.
pg 001-032/V520/21-Eng 12/11/01, 5:05 PM 18