Linear ACCESS AE-100 User Manual

Page 18

FUNCTION CODE

LOCAL PROGRAMMING

TELEPHONE PROGRAMMING

ADD A

STAND-ALONE

ACCESS CODE

A Stand-alone Access Code is
a number entered at the AE-100
keypad to request access. Up to
125 4-digit Stand-alone Access
Codes can be set.

NOTE: Each Stand-alone Access
Code programmed reduces the
possible number of Directory
Entries by one.

Step 1 Enter Function Code 31, then press #.

Step 2 Enter the new 4-digit Stand-alone

Access Code, then press #.

Step 3 Enter the new 4-digit Stand-alone

Access Code again for verifi cation

Step 4 Press #.

Step 1 Enter Function Code 31 and

press #, one short beep sounds.

Step 2 Enter the new 4-digit Stand-alone Access

Code, press #, one short beep sounds.

Step 3 Enter the new 4-digit Stand-alone

Access Code again for verifi cation.

Step 4 Press #, two short beeps sound.

DELETE A

STAND-ALONE

ACCESS CODE

Deletes a single existing
Stand-alone Access Code.

Step 1 Enter Function Code 33, then press #.

Step 2 Enter the 4-digit Stand-alone Access

Code to delete, then press #.

Step 3 Enter the 4-digit Stand-alone Access

Code to delete again for verifi cation

Step 4 Press #.

Step 1 Enter Function Code 33 and

press #, one short beep sounds.

Step 2 Enter the 4-digit Stand-alone Access Code

to delete, press #, one short beep sounds.

Step 3 Enter the 4-digit Stand-alone Access

Code to delete again for verifi cation.

Step 4 Press #, two short beeps sound.

COPY ALL MASTER

MEMORY TO

SUB-UNITS

To synchronize programming
in multi-unit installations, all
system data can copied from the
master unit to selected sub-units.
This data includes the Directory
Entries, Stand-alone Access
Codes, and all system option
settings (except the sub-unit
number).

NOTE: This utility command
can only be performed from the
“master” unit

CAUTION: This utility

command will overwrite ALL
data in the sub-unit(s) selected.

Step 1 Enter Function Code 34, then press #.

Step 2 Enter the number(s) (2, 3, and/or 4) of all the

sub-units to copy the data to, then press #.

Step 3 Enter 5 for verifi cation, then press #.

- OR -

Enter

✱ to cancel this command.

NOTE: The installer must setup the system as a multi-unit

installation before this command will operate.

Step 1 Enter Function Code 34 and

press #, one short beep sounds.

Step 2 Enter the number(s) (2, 3, and/or 4)

of all the sub-units to copy the data to,
then press #, one short beep sounds.

Step 3 Enter 5 for verifi cation, then press #,

two short beeps sound. (Any entry other
than 5# will cancel the command.)

NOTE: To allow for multi-unit network

communications, when executing this
command remotely over the telephone,
the system will disconnect your call
after Step #3 then copy the data from
the master unit to the sub-units.

SYSTEM DISPLAY

LANGUAGE

The factory default language is
English. Three other languages
can be selected as the language
for the user and programming
displays.

NOTE: The system supports one
display language at a time.

Step 1 Enter Function Code 38, then press #.

Step 2 Enter:

1 for English (Default).

2 for Spanish.

3 for French.

4 for Portuguese.

Step 3 Press #.

NOT AVAILABLE

A C C E S S C O D E :

U N I T S :

A R E Y O U S U R E ? 5

L A N G U A G E : 1 - 4

ALTERNATE PROGRAMMING METHOD