Lucent Technologies 9077 16S User Manual
Page 116
B-2
October 22, 1999
SP Switch Router Adapter Guide - 1.4 Update 2
Log Messages
Alphabetical list of messages
“RX: send SEND_TOD to the switch.” . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
“RX: Reading TBIC's TOD .” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
“RX-TBIC outage error(s) detected IER1=0x%x, IER2=0x%x..,” . . . . . . B-10
“RX-TBIC permanent error(s) detected IER1=0x%x, IER2=0x%x..,” . . . B-10
“RX-TBIC transient error(s) detected IER1=0x%x, IER2=0x%x”, . . . . . B-11
“Rx timed-out, src_node=%d, msg_id=%d, bytes rxed: %d, . . . . . . . . . . B-11
“SEND TOD service message received” . . . . . . . . . . . . . . . . . . . . . . . . . . B-11
“Sending Grid Init” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-11
“Sending IF Init for IF 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-11
“Sending IF RESET message to TX-CPU.” . . . . . . . . . . . . . . . . . . . . . . . . B-11
“Sending mib-2 trap, type = %d, state = %d.” . . . . . . . . . . . . . . . . . . . . . . B-12
“Sending params to TX...” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-12
“State machine changes from xxx to yyy.”. . . . . . . . . . . . . . . . . . . . . . . . . B-12
“State machine changes from xxx to yyy.”. . . . . . . . . . . . . . . . . . . . . . . . . B-12
“Status/Err service message received.”. . . . . . . . . . . . . . . . . . . . . . . . . . . . B-13
“Svc Msg rxed, svc_cmd=0x%x %s, node_cmd: 0x%x %s.” . . . . . . . . . . B-13
“Switch received with errors. Descriptor: 0x%8x.” . . . . . . . . . . . . . . . . . . B-13
“Switch route entry not found, node = %d.” . . . . . . . . . . . . . . . . . . . . . . . B-13
“Switch Route table loaded, %d entries.”. . . . . . . . . . . . . . . . . . . . . . . . . . B-14
“TB4 segment received in error.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-14
"TB4-HDR word%d: 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-14
“TB4 segment received in wrong state.” . . . . . . . . . . . . . . . . . . . . . . . . . . B-14
“TBIC INIT msg sent to TX-CPU.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-14
“TBSI Online Init the ORCAs.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-15
“TBSI-RX: TBIC's TOD: 0x%x, 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . B-15
“TBSI-TX Unexpected SVC threshold interrupt.” . . . . . . . . . . . . . . . . . . . B-15
“TBUS Parity Error from RC, int1=%d.”. . . . . . . . . . . . . . . . . . . . . . . . . . B-15
“TBUS Parity Error from TC, int1=%d.” . . . . . . . . . . . . . . . . . . . . . . . . . . B-15
“Timeout waiting for CFG_DN bits clear, stat0=%x.” . . . . . . . . . . . . . . . B-16
“Timeout waiting for FPGA_INIT_COMPLETE, stat0=%x.” . . . . . . . . . B-16
“RX: got TBIC INITED from TX.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-16
“RX: Port connected, stat=0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-16
“RX: Setting the RC in operational mode, stat=0x%x.” . . . . . . . . . . . . . . B-17
“Timed out resolving ARP. If: %d IP: %d.%d.%d.%d.” . . . . . . . . . . . . . . B-17
“TX-CPU: Access FIFO busy, discarding IP packet.” . . . . . . . . . . . . . . . . B-17
“TX-CPU Config Params msg received from RX-CPU.” . . . . . . . . . . . . . B-17
“TX-CPU sending msg type=%d to RX-CPU.” . . . . . . . . . . . . . . . . . . . . . B-17
“TX-CPU TBIC Init msg received from RX-CPU.” . . . . . . . . . . . . . . . . . B-18
“TX: Port is connected, stat=0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-18
“TX-PROR: start_node: %d, end_node: %d, # entries: %d.”. . . . . . . . . . . B-18
“TX: pseudo STI clock is valid.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-18
“TX: Setting the TC in operational mode, stat= 0x%x.” . . . . . . . . . . . . . . B-18
“TX clearing interrupts, i0=0x%x, i1=0x%x.” . . . . . . . . . . . . . . . . . . . . . . B-18
“TX-TBIC outage error(s) detected IER1=0x%x, IER2=0x%x,” . . . . . . . B-19
“TX-TBIC permanent error(s) detected IER1=0x%x, . .” . . . . . . . . . . . . . B-19
“TX-TBIC transient error(s) detected IER1=0x%x, IER2=0x%x,” . . . . . . B-19
“Un-expected descriptor from RC, desc_type=%d.” . . . . . . . . . . . . . . . . . B-19
“Un-expected descriptor from TC, desc_type=%d.” . . . . . . . . . . . . . . . . . B-19