Lucent Technologies 9077 16S - Manual (Page 115)

SP Switch Router Adapter Guide - 1.4 Update 2 October 22, 1999 B-1
B Log Messages
This appendix contains brief explanations of log messages that are generated by the SP Switch
Router Adapter card. You will see most of them in the
/var/log/gr.console file.
Alphabetical list of messages
The first line of each error message and the page on which it appears are listed here:
“Access FIFO Sync Error from RC, int1=%d”. . . . . . . . . . . . . . . . . . . . . . . B-3
“Access FIFO Sync Error from TC, int1=%d”. . . . . . . . . . . . . . . . . . . . . . . B-3
"ACK WORDS: 0x%08x, 0x%08x, 0x%08x, 0x%08x, ” . . . . . . . . . . . . . . B-3
“ARP added: IP= %s, SW-node=%d, state=%d” . . . . . . . . . . . . . . . . . . . . . B-4
“Bad Hdr/Svc received, Ret code=%d” . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
“Board Configuration timed-out, retrying” . . . . . . . . . . . . . . . . . . . . . . . . . B-4
“Broadcasting an ARP Request.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-4
“Broadcasting a Gratuitous ARP Request” . . . . . . . . . . . . . . . . . . . . . . . . . B-4
“Configuration Parameters:”. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
“Configuring transmit side.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-5
“CPU ready msg received from TX-CPU”. . . . . . . . . . . . . . . . . . . . . . . . . . B-5
“Descriptor Sync Error from RC, int1=%d” . . . . . . . . . . . . . . . . . . . . . . . . B-6
“Descriptor Sync Error from TC, int1=%d”. . . . . . . . . . . . . . . . . . . . . . . . . B-6
“Discarding msg, unknown msg_type 0x%x” . . . . . . . . . . . . . . . . . . . . . . . B-6
“ERR! Duplicated buffer %d” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-6
“Expect NODE_INIT but received Stat/Err Request” . . . . . . . . . . . . . . . . . B-7
“Expired IP buffer received: %d” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
“Hot interrupt detected, ier1=0x%8x, ier2=0x8x” . . . . . . . . . . . . . . . . . . . . B-7
“Hot interrupt detected, ier1=0x%8x, ier2=0x8x” . . . . . . . . . . . . . . . . . . . . B-7
“Initializing Main Task...” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-7
“Initializing RX Subsystem data structure.”. . . . . . . . . . . . . . . . . . . . . . . . . B-8
“IOSTB3:RX SET TOD service message received.” . . . . . . . . . . . . . . . . . . B-8
“Loopback routes found for IP adr: 0x%x, sw-node.” . . . . . . . . . . . . . . . . . B-8
“Lost of STI clock, TBIC Status = 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . B-8
“Lost of STI clock, TBIC Status = 0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . B-8
“NetStar GigaRouter %s RX Interface Initializing:” . . . . . . . . . . . . . . . . . . B-9
“NetStar GigaRouter %s TX Interface Initializing:” . . . . . . . . . . . . . . . . . . B-9
“RX: Clock is valid.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-9
“RX-CPU Loaded msg received from TX-CPU.” . . . . . . . . . . . . . . . . . . . . B-9
“RX: got TBIC INITED from TX.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10
“RX: Port connected, stat=0x%x.” . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . B-10