Linn PRE- AMPLIFIER - Manual (Page 20)

R RC CU U//IIR R S SO OC CK KE ET T
Define the use of the socket marked RCU on the back panel.
Options: R RC CU U** (KNEKT Room Control Unit), IIR R (Infrared Repeater)
Default setting: R RC CU U
* For use with Linn KNEKT systems only.
P PR RO OD DU UC CT T IIR R
Enable or disable the infrared receiver on the front of the unit.
Options: E EN NA AB BL LE ED D,, D DIIS SA AB BL LE ED D
Default setting: E EN NA AB BL LE ED D
R RS S2 23 32 2 S SE ET TU UP P
Accesses the RS232 SETUP sub-menu.
The RS232 Setup sub-menu is for use if the AKURATE KONTROL is
communicating with other RS232 enabled products (e.g. a third-party
controller).
B BA AU UD D R RA AT TE E
Set the baud rate to suit the RS232 protocol being used.
Range: 4 48 80 00 0 tto o 2 23 30 04 40 00 0 (9 settings)
Default setting: 9 96 60 00 0
P PA AR RIIT TY Y
Set parity to suit the RS232 protocol being used.
Options: E EV VE EN N,, O OD DD D,, N NO ON NE E
Default setting: E EV VE EN N
D DA AT TA A B BIIT TS S
Set the data bits to suit the RS232 protocol being used.
Options: 7 7,, 8 8
Default setting: 7 7
S SE EL LE EC CT TIIO ON N T TIIM ME EO OU UT T
Set the time the AKURATE KONTROL takes to select a source when
the source is changed.
Range: 1 1 S SE EC C.. tto o 1 10 0 S SE EC C..
Default setting: 2 2 S SE EC C..
S ST TA AR RT TU UP P S SO OU UR RC CE E
Set the source the AKURATE KONTROL selects when brought out of
standby.
Options: L LA AS ST T U US SE ED D,, N NO ON NE E,, ((a an ny y o off tth he e s so ou urrc ce e iin np pu utts s))
Default setting: L LA AS ST T U US SE ED D
S ST TA AN ND DB BY Y R RE EC CO OR RD D F FR RO OM M
You can record from a source component to a recording device
through the AKURATE KONTROL, even if the AKURATE KONTROL is
in standby mode.* Set which source you want the AKURATE
KONTROL to select when it is in standby.
Options: L LA AS ST T U US SE ED D,, N NO ON NE E,, ((a an ny y o off tth he e s so ou urrc ce es s)),, K KN NE EK KT T****
Default setting: L LA AS ST T U US SE ED D
* For information on setting-up a record path see Record function,
page 23.
** Is only available when KNEKT (see below) is set to LOCAL ROOM.
K KN NE EK KT T
If your AKURATE KONTROL is installed in a Linn KNEKT multi-room
system, select the appropriate setting. If your AKURATE KONTROL is
not installed in a KNEKT system, select N
NO ON NE E.
Options: N NO ON NE E,, M MA AIIN N R RO OO OM M,, L LO OC CA AL L R RO OO OM M,, IIN NT TE ER RS SE EK KT T
Default setting: N NO ON NE E
ENGLISH
12 AKURATE KONTROL
AKURATE KONTROL pre-amplifier - english 15/5/07 15:17 Page 20