Kenwood KXF-W4010 - Manual (Page 22)

CT-2050/203/KXF-W6010/W4010 (En/M)
22
Convenient CD recording (CT-203/KXF-W4010; Deck B only)
Recording of CD playback (CCRS) (Deck B only)
1
Insert a tape in deck B.
2
Determine the recording condition.
1 Select the recording mode.
3
When connected with a KENWOOD amplifier,CD player provided with " f", "ƒ", " ( ƒ)" marking through the
system control cord, this unit allows to use the CCRS, which starts recording automatically after setting the optimum recording
level for the CD and tape to be used in recording.
Since this unit is not designed for recording with metal (TYPE ) tapes, do not use metal tapes for recording.
Press the CCRS key.
How to cancel CCRS
÷ For the tape direction setting, see the description below “Select the
tape transport direction”. 0
2
Select the Dolby NR mode.
1. If the CCRS key is pressed during CD playback, playback stops and CCRS operation begins.
2 .If the remaining amount of tape is small, CCRS may not function correctly or CCRS operation may be canceled in mid-operation.
3 .Once the CCRS recording level has been set, the recording balance and recording level cannot be adjusted while the CCRS operation
is being carried out.
4 .The CCRS function sets the peak level for the entire CD in approx. 20~200 seconds. On very rare occasions, however, the function
may not be able to set the optimum recording level. If this occurs, carry out recording manually referring to the “Normal recording”
section.
^
5. The CCRS recording level setting is canceled when the open/close key of the CD player is pressed or when the power is switched OFF.
6. With CD players equipped with the EDIT function, it is possible to make recordings in which the last songs on sides A and B are not cut
off in the middle and in which the recording capacity of the tape is used to the fullest extent. (Set the REV.MODE key of the deck to “ [”.)
During recording level setting:
Press the Stop key of the CD player or the stop key
of the cassette deck.
During CCRS recording:
Press the Stop key of the CD player, then press the
OPEN / CLOSE key of the CD player.
After completion of CCRS recording:
Press the OPEN / CLOSE key of the CD player.
Preparation 1
Complete the connections referring to
"System connections".
6
2
(Set the input selector of the amplifier to
CD.)
3 (Load a disc in the CD player.)
(Edit tracks as required on the CD player.)
÷ After recording, the cassette deck and CD player enter the stop
mode automatically.
÷ After completion of CCRS recording , be sure to cancel the CCRS
and ensure that the CCRS indicator has gone off.
÷ Program-edit recording is not possible when tracks of more than one
CD are programmed using a Carrousel type CD player.
÷ When performing CCRS recording with a CD player which can be
loaded multiple compact discs, set the CD palyer to TRACK mode,
press the disc selector key and press the CCRS key of the cassette
deck.
÷ The CCRS indicator blinks, and actual recording starts in about 20 to 200
seconds (after creating a non-recorded blank of about 8 seconds).
Each press switches the indication.
1 “ [ [ [ [ [” :Double-side recording.
2 “ ” ” ” ” ”” :(Tape also stops after having recorded both sides.)
3 “ “ “ “ “ “” :One-way recording.
Each press switches the indication.
1 DOLBY NR “OFF” (extinguished): Dolby NR is not used.
2 DOLBY NR “B”: Noise reduction of the ordinary type.
3 DOLBY NR “C”: Noise reduction with higher performance.
: Keys and control used in the operations described on this page.
REV.MODE
DOLBY NR
CCRS
CT-2050/KWF-W6010
CT-203/KXF-W4010
Notes Notes