Kodak EKTAPRO 9020 - Manual (Page 18)

35
Accessories
• KODAK EKTAPRO Extra Bright Lamp Modules
Single Lamp Module for EKTAPRO 3020 Projector:
European CAT No. 718 3379
Dual Lamp Module (ALC) for EKTAPRO 4020, 5020, 7020, 9020:
European CAT No. 718 4369
• KODAK EKTAPRO Standard Heatfilter for Extra Bright Lamp
Modules for the reduction of slide temperature and brightness
(conforms with the 3000, 3010, 4010, 7000, 9000 and 9010 models).
European CAT No 717 7140
• KODAK EKTAPRO Heatfilter +10 for Extra Bright Lamp
Modules for the reduction of slide temperature and brightness
(conforms with all previous models already equipped with such
filters). European CAT No 717 7157
• KODAK EKTAPRO IR Remote Receiver RA
European CAT No. 712 8606
This receiver is necessary for operating another projector in
parallel via the EKTAPRO IR Remote Controls.
• Projection Lamps
There are three different projection lamps for varying projection
conditions available for your EKTAPRO Slide Projector:
EXR 82V/35h 300W European CAT No. 145 2259
Brightness: 100% (standard value)
FHS 82V/70h 300W European CAT No. 147 7678
Brightness: 80%
EXY 82V/200h 250W European CAT No. 145 2143
Brightness: 60%
• KODAK EKTAPRO Carrying Case
European CAT No. 718 1993
Hard case for projector, lens, tray and remote control transporta-
tion.
• KODAK EKTAPRO Twin Socket Adapter
European CAT No. 712 5909
This adapter allows linkage of an additional projector in parallel
and an EKTAPRO Cable Remote. The adapter will fit into the
remote control socket.
• KODAK EKTAPRO Twin Socket Connecting Cable / 2 m
European CAT No. 712 5917
To connect an additional EKTAPRO Slide Projector to the Twin
Socket Adapter for a projection in parallel.
• KODAK EKTAPRO 4 x 4 Condenser Kit
Europ. Cat. No. 714 4967
For projecting 4 x 4 slides (superslides) for the KODAK 36, 85, 93,
100, 150 and 180 mm Projection FF Lenses!
• KODAK EKTAPRO 1 m Dissolve Cable
Europ. Cat. No. 715 3992
You can connect a second projector with a P-Bus-in interface to
an EKTAPRO 7020 or 9020 for the dissolve mode (or parallel mode).
• KODAK Slide Projection FF Lenses
(lens summary, page 85)
• KODAK EKTAPRO Lens Support -the lens support for large and
heavy lenses. European CAT No. 715 1335
• KODAK EKTAPRO 80 Slide Tray with transparent cover.
European CAT No. 712 8580
Trays are available for holding 80 slides.
• KODAK CAROUSEL TRANSVUE 140 Slide Tray
European CAT No. 184 0768 (not widely available in Europe).
• KODAK EKTAPRO Cable Remote (4 m)
European CAT No. 712 1080
Control of slide change, focus and standby.
• KODAK EKTAPRO Remote Extension Cable / 8 m
European CAT No. 712 5925
Using the EKTAPRO Cable Remote:
Up to three of these cables can be joined together giving a possible
operation length of up to 28 m.
Using the EKTAPRO IR Remote Receiver RA:
The receiver can be installed up to 8 m away from your projector
with this cable.
• KODAK EKTAPRO IR Remote System RA
European CAT No. 712 1072
The remote control consists of a transmitter and a receiver. The
receiver has been constructed so that it can fit directly into the
remote control socket (25).
Furthermore, you can choose between two channels which enable
use of two IR remote controls to control two different projectors
in one room. The receiver does not need batteries as it receives
electricity through the 8-pin remote control socket (25), from the
projector.
With this remote system, you can control the functions standby,
slide change and focus. With the ten key keypad you can select
any slide in the slide tray. With models 7020 and 9020 you can use
this keypad to transfer a series of additional interesting functions
such as inputting a dissolve time, autotimer, freeze, reset etc.
The keypad has a sliding cover for storage.
• KODAK EKTAPRO IR Remote System RA/LP
European CAT No. 712 1064
This remote, in addition to above features, has a built-in laser
pointer with an illuminous red point for emphasizing important
picture content on the screen.
• KODAK EKTAPRO 12/7-Pin Module
European CAT No. 712 5875
• KODAK EKTAPRO 12/7-Pin Adapter Cable
European CAT No. 712 5883
With the module and the adapter cable you can connect many
dissolve devices, those for the KODAK CAROUSEL S-AV and
EKTAGRAPHIC projectors (12 or 7 pin standard).