Kenwood KAC-X4R - Manual (Page 8)

8 English
Item Setting value Ach Bch LINE OUT
LN.SEL ST / CT/SW (Default setting value : ST) Ч Ч
ST
(When LN.SEL. is
set to “ST”)
CTR
(When LN.SEL. is
set to “CT/SW”)
SW
(When LN.SEL. is
set to “CT/SW”)
LEVEL -20 – 0 (Default setting value : 0) Ч Ч
BAND1
(Parametric EQ-1)
FREQ (Hz)
(Mean frequency)
25/40/60/80/100 (Default setting value : 25)
×
Q 1.0/2.0/3.0/5.0 (Default setting value : 1.0)
GAIN -9 – +9 (Default setting value : 0)
BAND2
(Parametric EQ-2)
FREQ
150/200/300/400/500
(Default setting value : 150)
×
Q 1.0/2.0/3.0/5.0 (Default setting value : 1.0)
GAIN -9 – +9 (Default setting value : 0)
BAND3
(Parametric EQ-3)
FREQ 600/800/1k/1.5k/2k (Default setting value : 600)
× Q 1.0/2.0/3.0/5.0 (Default setting value : 1.0)
GAIN -9 – +9 (Default setting value : 0)
BAND4
(Parametric EQ-4)
FREQ 3k/4k/5k/6.3k (Default setting value : 3k)
× Q 2.0/4.0/8.0/10 (Default setting value : 2.0)
GAIN -9 – +9 (Default setting value : 0)
BAND5
(Parametric EQ-5)
FREQ 8k/10k/12.5k/16k (Default setting value : 8k)
× Q 2.0/4.0/8.0/10 (Default setting value : 2.0)
GAIN -9 – +9 (Default setting value : 0)
LPF
(Low Pass Filter) FREQ
Low
TH/30/40/50/60/70/80/90/100/120/150/180/220/
250 (Default setting value : TH)
Ч Ч
High
500/630/800/1k/1.25k/1.6k/2k/2.5k/3.15k/4k/5k
(Default setting value : TH)
Ч Ч Ч Ч
SLOPE −24/−12 (Default setting value : -12) Ч Ч
ISF
(Infrasonic Filter)
FREQ
TH/20/30/40/50/60
(Default setting value : TH)
Ч Ч Ч Ч
HPF
(High Pass Filter) FREQ
Low
TH/30/40/50/60/70/80/90/100/120/150/180/220/
250 (Default setting value : TH)
×
High
500/630/800/1k/1.25k/1.6k/2k/2.5k/3.15k/4k/5k
(Default setting value : TH)
Ч Ч Ч Ч
SLOPE −24/−12 (Default setting value : -12) ×
DELAY
L 0 – 3.9 (Default setting value : 0)
(L/R is not
differentiated)
×
R 0 – 3.9 (Default setting value : 0) ×
PHASE -180/0 (Default setting value : 0) ×
DSP Settings
Perform DSP settings for channels A, B and LINE OUT.
Setting
1 Slide the DISP switch towards SET.
2 Slide the MODE switch to set the channel (“Ach”, “Bch” or “LINE OUT”).
3 Turn the control knob, display the item to set and push the control knob.
Repeat this step until the item to set is displayed.
To return to the previous menu, turn the control knob, display “RTN” and press the
control knob.
4 Turn the control knob, display the value to set and press the control knob. The
displayed value is set.
Control knob
DISP switch MODE switch
Items and setting values
NOTE
• For LPF, HPF must be set to “TH”.
• For ISF, HPF must be set to “TH”.
• For HPF, LPF and ISF must be set to “TH”.
• If LPF and ISF are set simultaneously, LPF frequency cannot be lower than ISF frequency.
NOTE
• If speakers are bridged, set “L” and “R” for “DELAY” to the same value. Effects will not be applied properly if they are set to different values.
• DSP settings will not be cleared even when the reset button is pressed.