Sharp 28LF-92H - Manual (Page 18)

- 17 -
• Press “ “ button to stop the automatic page change.
• Press “
“ button again to allow the next page to be dis-
played.
To Select a Subcode Page
Subcode pages are subsections of long Teletext pages that
can only be displayed on the screen one section at a time.
• Select the required Teletext page.
• Press “
“ button.
• Select the required subcode page number by pressing four
digit buttons (e.g. 0001).
• If the selected subcode page is not displayed in a short
time, press “ “ button. TV programme will be displayed on
the screen.
• Teletext page number will be displayed on the upper left
corner of the screen when the selected page is found.
• Press “ “button to display the selected Teletext page.
Fastext
Teletext mode will be selected according to transmission au-
tomatically.
Your TV supports the 7 page Teletext system. When the
page number of any of the 7 pages in memory is entered, the
system will not search for the requested page; instead it will
display the page automatically.
• Press “ ” button to move the Teletext screen forward one
page at a time.
• Press “ ” button to move the Teletext screen backward
one page at a time.
For Fastext
The subject-heading for the information may have a particular
colour or can be in a form located in a coloured box.
• Press an appropriate RED, GREEN, YELLOW or BLUE but-
ton in order to reach the relevant page quickly.
To exit Teletext
• Press “ 79 ” button. The screen will switch to TV mode.
Connecting external equipment
Via the Euro connector
You TV set has two euro connector sockets. If you wish to
connect external equipment (e.g. video recorder, decoder,
etc.) which have Euro connectors, to your TV, use the EXT.1
(EXT-1) or EXT.2 (EXT-2) terminals.
If an external device is connected via Euro connector sockets
the TV will be switched to AV mode automatically.
RGB mode
If a piece of equipment outputs RGB signals use the EXT-1
Euro connector as this is RGB ready.
Via the RCA jacks
If you have an equipment (such as a Camcorder) which has
the RCA jacks, connect it to the Front AV (F-AV) terminal
with the video and audio cables.
• If the equipment has the mono audio jack, connect it to the
AUDIO-L jack.
Via the ANT (aerial) socket
If your equipment does not have an Euroconnector or RCA
jacks, connect it to the TV with an aerial cable. For details,
see the manual provided with the equipment.
• To store the test signal that comes from the equipment,
see “INSTALL. Menu” on page 14 and store it to the pro-
gramme number 0. You can watch images from that equip-
ment to select the programme number which you stored the
test signal.
TV and Video Recoder (VCR)
• Connect the Video Recorder to the ANT (antenna input)
socket of the TV with the aerial cable.
• Connect the Video Recorder to the EXT.1 or EXT.2 terminal
with the SCART cable, or connect it to the Front AV (F-AV)
terminal with the audio and video cables.
NTSC Playback
Connect a NTSC video recorder to a terminal. Then press
“
(;7 ” button to select the corresponding AV mode.
NTSC 3.58/4.43 system is detected automatically in AV
mode.
Copy Facility
You can output the video and audio signals which inputs from
TV or EXT.1 (EXT-1) terminal to the video recorder connected
to the EXT.2 (EXT-2) terminal.
• To select the output source, see “Setting External
Source Output” on page 13.
To connect to S-VHS input
Connect your camera or camcorder at the front or back side
of your TV.
• Connect your equipment to the TV via S-VHS input and au-
dio inputs of F-AV inputs by using S-VHS cables.
Connecting Headphones
Use the stereo headphone socket of your TV, to connect
headphones.
ENG-2862W-3262W-1548UK-2SCART-FAV-SVHS-AK45-SHARP-TV-2.p65 21.01.2004, 08:29 17