beautypg.com

Setting the character pitch, Entering the pitch lock mode – Star Micronics HL 80825321 User Manual

Page 42

background image

31

Setting the character pitch

The character pitch setting controls how many characters are printed per inch. Use
the following procedure to select the pitch you want.

Make sure the printer is off-line (

ON LINE

indicator is not lit).

Press

PITCH

to change the pitch selection.

The following shows the meanings of the indicators that light on the control
panel when you press

PITCH

.

Entering the Pitch Lock Mode

When the printer is in the Pitch Lock Mode, the pitch settings you make on the
control panel are used even if your software sends a different pitch. Use the
following procedure to enter the Pitch Lock Mode.

Turn off the printer.

While holding down

PITCH

, turn printer power on.

The printer is now in the Pitch Lock Mode. You could enter the Pitch Lock
Mode and Font Lock Mode (page 29) at the same time by holding down both

FONT

and

PITCH

when you turn on printer power.

To exit the Pitch Lock Mode, Simply turn the printer off.

Indicators

Meaning

10CPI

10 characters per inch (Pica)

12CPI

12 character per inch (Elite)

10CPI + COND

17 characters per inch (Condensed Pica)

12CPI + COND

20 characters per inch (Condensed Elite)

10CPI + PROP

Pica Proportional

12CPI + PROP

Elite Proportional

10CPI + COND + PROP

Condensed Pica Proportional

12CPI + COND + PROP

Condensed Elite Proportional

Note:

The pitch setting you make with the above procedure can be changed if the software
you are using overrides the setting from the control panel. You can prevent this by
using the following procedure to put the printer into the Pitch Lock Mode when you
turn it on.

Réglage du pas des caractères

Le réglage du pas contrôle le nombre de caractères imprimés par pouce. Effectuez
les démarches suivantes pour sélectionner le pas.

Vérifiez que l’imprimante est hors ligne (voyant

ON LINE

éteint).

Appuyez sur

PITCH

pour sélectionner un autre pas.

Le tableau suivant indique les voyants qui s’allument sur le panneau de
commande quand vous appuyez sur

PITCH

.

Mode de verrouillage du pas

Quand l’imprimante est en mode de verrouillage du pas, les réglages de pas
effectués sur le panneau de commande sont utilisés même si le logiciel envoie une
commande différente. Effectuez les démarches suivantes pour entrer en mode de
verrouillage du pas.

Mettez l’imprimante hors tension.

Tout en tenant la touche

PITCH

enfoncée, mettez l’imprimante sous tension.

L’imprimante se trouve maintenant en mode de verrouillage du pas. Vous
pouvez sélectionner le mode de verrouillage du pas et le mode de verrouillage de
la police (page 29) en même temps en tenant les deux touches

FONT

et

PITCH

enfoncées quand vous mettez l’imprimante sous tension.

Pour annuler le mode de verrouillage du pas, mettez simplement l’imprimante
hors tension.

Voyants

Signification

10CPI

10 caractères par pouce (Pica)

12CPI

12 caractères par pouce (Elite)

10CPI + COND

17 caractères par pouce (Pica condensé)

12CPI + COND

20 caractères par pouce (Elite condensé)

10CPI + PROP

Pica proportionnel

12CPI + PROP

Elite proportionnel

10CPI + COND + PROP

Pica proportionnel condensé

12CPI + COND + PROP

Elite proportionnel condensé

Remarque:

Le pas que vous avez sélectionné peut changer si le logiciel que vous utilisez envoie
une commande de pas différente à l’ordinateur. Pour éviter cela, vous pouvez
mettre l’imprimante en mode de verrouillage du pas lors de la mise sous tension en
effectuant les démarches suivantes.