Stanton S-700 - Manual (Page 8)

7. Cueing
"Cueing" is the action of preparing for playback; when
the Cue button(14) is pressed, playback returns to the
cue point and enters pause mode. When the
PLAY/PAUSE button(22) is pressed during the cue
mode, playback starts.
Cue point setting:
A. Playback starts from pause ( using the jog wheel to
set the starting point ) or skip to a new track during
play or pause.
The beginning play point will be set to the cue point.
Or
B. Press the IN/R.CUE button(15) during playback to
set the new cue point.
Or
C. Memorize any of 10 CUE points by pressing
MEMORY(3) to set desired Cue then press any of 10
number buttons(4).
To return to Cue point press Cue Button(14). This will
return to point A or B above.
The player has completed the cue or pause operation
and is waiting for the play start command.
When the PLAY/PAUSE button(22) is pressed,
playback starts.
D. To recall cues, if the recall LED is lit you can press
the last number button cue stored and create a
STUTTER EFFECT (see also p8). The last cue that
was stored or recalled will flash in the LED screen to
let you know it was last cued up.
8.Auto cue
When disk is loaded, the cue point is set to the first
source of music.
If track is changed before pressing play, the cue point is
changed to the new starting point.
If you pause during playback this also sets the new cue
point.
9.Frame search
This is done by first pausing then using the jog wheel(13)
to set the starting point. (When you use the jog wheel
the monitor function allows you to hear what is playing.
Once you have set starting point press PLAY(22) then
CUE(14) to again mute output.)
10.Scanning (fast forward/fast reverse )
To do this rotate Shuttle wheel(12) forward or reverse
You will scan or reverse at 4 different speeds
depending on how much you rotate the wheel.
11.Loop play
You can create a seamless loop between two points
continuously.
(1) Press PLAY/PAUSE BUTTON (22) so a CD is playing.
The PLAY/PAUSE BUTTON’S LED lights (figure 1).
(2) Press IN/R. CUE BUTTON (15). This sets the
starting point of the SEAMLESS LOOP. The
IN/R.CUE LED will light (figure 2).
(3) Press OUT/EXIT BUTTON (16) to set desired ending
point of the SEAMLESS LOOP. You will know you are
in SEAMLESS LOOP mode because IN/R.CUE and
OUT/EXIT LEDs will light and flash. LOOP
INDICATOR (8) in LCD DISPLAY will also flash.
Sound will continue with no interruption (SEAMLESS
LOOP)(figure 3).
(4) To exit SEAMLESS LOOP, press OUT/EXIT
BUTTON (16). LEDs will stay on but not flash. Music
will resume normal play (figure 4).
(5) To replay loop, press the RELOOP BUTTON (17).
IN/R.CUE and OUT/EXIT LEDs and LOOP
INDICATOR(8) in LCD DISPLAY will all begin
flashing again (figure 5).
12.SEAMLESS LOOP PLAY (CONT.)
(1) (Must be in SEAMLESS LOOP mode). If a
SEAMLESS LOOP has not been created, follow
instructions on this page for creating a SEAMLESS
LOOP. If a SEAMLESS LOOP has already been
created, press RELOOP BUTTON (17) to reenter the
SEMALESS LOOP mode (figure 5).
(2) Next, press OUT/EXIT BUTTON (16) to return to
normal play (figure 6). This disengages the
SEAMLESS LOOP mode.
(3) Press OUT/EXIT BUTTON (16) again for new desired
ending point of the loop (figure 7).
FOR SHORTER LOOP: press OUT/EXIT BUTTON
(16) quickly.
FOR LONGER LOOP: Wait until the song plays
several frames, then press OUT/EXIT BUTTON (16).
NOTE: YOU CAN ONLY EDIT THE ENDING PART OF
THE LOOP.
Fig.5
Fig.4 Fig.7
Fig.3 Fig.6
Fig.2
PLAY
PAUSE
Fig.1
13.SLEEP MODE
The CD player automatically shuts off the transport and
laser after 15 minutes (when in pause or cue mode).
This will lengthen the life of your motor drive and laser.
To restart player, just press cue(14) or play(22) buttons.
7